bug#62504: closed (30.0.50; SEGFAULT On M-x)

[GNU bug Tracking System]

Your message dated Mon, 11 Sep 2023 16:56:55 -0700
with message-id 
<CADwFkmneZ6Tu0ET0tvthyRt0LCQJHNLvwqpCHJy+XoJOVZVMWA@mail.gmail.com>
and subject line Re: bug#62504: 30.0.50; SEGFAULT On M-x
has caused the debbugs.gnu.org bug report #62504,
regarding 30.0.50; SEGFAULT On M-x
to be marked as done.

(If you believe you have received this mail in error, please contact
help-debbugs@gnu.org.)


-- 
62504: https://debbugs.gnu.org/cgi/bugreport.cgi?bug=62504
GNU Bug Tracking System
Contact help-debbugs@gnu.org with problems

--- Begin Message --- Subject: 30.0.50; SEGFAULT On M-x Date: Tue, 28 Mar 2023 11:25:49 -0400

Hello,

This bug is twofold and appears to be related to bug#62446 and bug#61917. I 
produce a much smaller reproducer that generates the same kind of error as 
bug#61917, namely `(wrong-number-of-arguments #<subr signal> 2)`. Segfaults 
only occur after the following commit:

commit 52b67740d10df8ca539fdc2c7d50283997683141
Author: Mattias Engdegård <mattiase@acm.org>
Date:   Sat Mar 25 15:38:00 2023 +0100

    Generalise a LAP optimisation rule

    * lisp/emacs-lisp/byte-opt.el (byte-optimize-lapcode):
    Accept (stack-set 1) as equivalent to (discardN-preserve-tos 1) in a
    rule previously overlooked.  This is usually beneficial in code size
    and almost always shortens dynamic paths.


Common setup:

1. mkdir repro
2. Put attached init.el and main.c inside (technically, main.c need not be in 
repro)

———

To reproduce bug#61917:

1. git checkout master
2. configure --with-native-compilation \
  --without-x \
  --without-ns \
  --without-compress-install \
  --with-native-compilation \
  --with-json \
  --with-tree-sitter
3. make bootstrap
4. emacs  --init-directory ../repro
5. Check messages, and ye shall find the bug message.

——— 

To reproduce segfault:

1. git checkout 52b67740d10df8ca539fdc2c7d50283997683141
2. Perform same configure and build commands as above.
3. emacs --init-directory ../repro ../repro/main.c (loading main.c is 
*required*, the segfault does not fire otherwise)
4. (In emacs) M-x
5. Fatal error 11: Segmentation fault

Best regards,

Jacob Faibussowitsch
(Jacob Fai - booss - oh - vitch)

main.c
Description: Binary data

init.el
Description: Binary data

config.log
Description: Binary data

--- End Message ---

> --- Begin Message ---
>
>
>
> Subject: 
>
> Re: bug#62504: 30.0.50; SEGFAULT On M-x
>
>
>
>
> Date: 
>
> Mon, 11 Sep 2023 16:56:55 -0700
>
>
>
>
> Jacob Faibussowitsch <jacob.fai@gmail.com> writes:
>
> > Segfaults and errors are gone with this change.
>
> It seems like this issue was fixed, but it was left open in the bug
> tracker.  I'm therefore closing it now.
>
>
> --- End Message ---