[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Qemu-devel] [PATCH v3 0/5] Add migration support for VFIO device
From: |
Kirti Wankhede |
Subject: |
[Qemu-devel] [PATCH v3 0/5] Add migration support for VFIO device |
Date: |
Wed, 20 Feb 2019 02:53:15 +0530 |
Add migration support for VFIO device
This Patch set include patches as below:
- Define KABI for VFIO device for migration support.
- Added save and restore functions for PCI configuration space
- Generic migration functionality for VFIO device.
* This patch set adds functionality only for PCI devices, but can be
extended to other VFIO devices.
* Added all the basic functions required for pre-copy, stop-and-copy and
resume phases of migration.
* Added state change notifier and from that notifier function, VFIO
device's state changed is conveyed to VFIO device driver.
* During save setup phase and resume/load setup phase, migration region
is queried and is used to read/write VFIO device data.
* .save_live_pending and .save_live_iterate are implemented to use QEMU's
functionality of iteration during pre-copy phase.
* In .save_live_complete_precopy, that is in stop-and-copy phase,
iteration to read data from VFIO device driver is implemented till pending
bytes returned by driver are not zero.
* Added function to get dirty pages bitmap for the pages which are used by
driver.
- Add vfio_listerner_log_sync to mark dirty pages.
- Make VFIO PCI device migration capable. If migration region is not provided by
driver, migration is blocked.
Below is the flow of state change for live migration where states in brackets
represent VM state, migration state and VFIO device state as:
(VM state, MIGRATION_STATUS, VFIO_DEVICE_STATE)
Live migration save path:
QEMU normal running state
(RUNNING, _NONE, _RUNNING)
|
migrate_init spawns migration_thread.
(RUNNING, _SETUP, _RUNNING|_SAVING)
Migration thread then calls each device's .save_setup()
|
(RUNNING, _ACTIVE, _RUNNING|_SAVING)
If device is active, get pending bytes by .save_live_pending()
if pending bytes >= threshold_size, call save_live_iterate()
Data of VFIO device for pre-copy phase is copied.
Iterate till pending bytes converge and are less than threshold
|
migration_completion() stops vCPUs and calls .save_live_complete_precopy
for each active device. VFIO device is then transitioned in
_SAVING state.
(FINISH_MIGRATE, _DEVICE, _SAVING)
For VFIO device, iterate in .save_live_complete_precopy until
pending data is 0.
(FINISH_MIGRATE, _DEVICE, 0)
|
(FINISH_MIGRATE, _COMPLETED, 0)
Migraton thread schedule cleanup bottom half and exit
Live migration resume path:
Incomming migration calls .load_setup for each device
(RESTORE_VM, _ACTIVE, 0)
|
For each device, .load_state is called for that device section data
|
At the end, called .load_cleanup for each device and vCPUs are started.
(RUNNING, _NONE, _RUNNING)
Note that:
- Migration post copy is not supported.
- VFIO device driver version compatibility is not taken care in this series.
v2 -> v3:
- Removed enum of VFIO device states. Defined VFIO device state with 2 bits.
- Re-structured vfio_device_migration_info to keep it minimal and defined action
on read and write access on its members.
v1 -> v2:
- Defined MIGRATION region type and sub-type which should be used with region
type capability.
- Re-structured vfio_device_migration_info. This structure will be placed at 0th
offset of migration region.
- Replaced ioctl with read/write for trapped part of migration region.
- Added both type of access support, trapped or mmapped, for data section of the
region.
- Moved PCI device functions to pci file.
- Added iteration to get dirty page bitmap until bitmap for all requested pages
are copied.
Thanks,
Kirti
Kirti Wankhede (5):
VFIO KABI for migration interface
Add save and load functions for VFIO PCI devices
Add migration functions for VFIO devices
Add vfio_listerner_log_sync to mark dirty pages
Make vfio-pci device migration capable.
hw/vfio/Makefile.objs | 2 +-
hw/vfio/common.c | 31 ++
hw/vfio/migration.c | 714 ++++++++++++++++++++++++++++++++++++++++++
hw/vfio/pci.c | 117 ++++++-
hw/vfio/pci.h | 29 ++
include/hw/vfio/vfio-common.h | 20 ++
linux-headers/linux/vfio.h | 65 ++++
7 files changed, 971 insertions(+), 7 deletions(-)
create mode 100644 hw/vfio/migration.c
--
2.7.0
- [Qemu-devel] [PATCH v3 0/5] Add migration support for VFIO device,
Kirti Wankhede <=
- [Qemu-devel] [PATCH v3 2/5] Add save and load functions for VFIO PCI devices, Kirti Wankhede, 2019/02/19
- [Qemu-devel] [PATCH v3 1/5] VFIO KABI for migration interface, Kirti Wankhede, 2019/02/19
- [Qemu-devel] [PATCH v3 3/5] Add migration functions for VFIO devices, Kirti Wankhede, 2019/02/19
- [Qemu-devel] [PATCH v3 4/5] Add vfio_listerner_log_sync to mark dirty pages, Kirti Wankhede, 2019/02/19
- [Qemu-devel] [PATCH v3 5/5] Make vfio-pci device migration capable., Kirti Wankhede, 2019/02/19
- Re: [Qemu-devel] [PATCH v3 0/5] Add migration support for VFIO device, Dr. David Alan Gilbert, 2019/02/20