[avrdude-dev] -c jtagmkII -P usb not working

[avrdude]

Hallo
I want to program my new xmega128a1 toy with:
/usr/local/bin/avrdude -c jtagmkII -P usb -p x128a1 -U flash:w:blink.hex -vv
but it not even found the signatur. -F also failed.
May someone have a idea on this output:
=====================================
ben:/home/axel/ufe/svn/trunk/c/avr/test/xm_blink# /usr/local/bin/avrdude -c 
jtagmkII -P usb -p x128a1 -U flash:w:blink.hex -vv

avrdude: Version 5.6cvs, compiled on May  7 2009 at 13:31:49
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/

         System wide configuration file is "/usr/local/etc/avrdude.conf"
         User configuration file is "/root/.avrduderc"
         User configuration file does not exist or is not a regular file, 
skipping

         Using Port                    : usb
         Using Programmer              : jtagmkII
avrdude: jtagmkII_open()
avrdude: usbdev_open(): Found JTAGICE mkII, serno: 00B0000064AA
avrdude: usbdev_open(): using read endpoint 0x82
avrdude: jtagmkII_getsync(): Sending sign-on command: 0x86 (28 bytes msg)
JTAG ICE mkII sign-on message:
Communications protocol version: 1
M_MCU:
  boot-loader FW version:        255
  firmware version:              5.44
  hardware version:              0
S_MCU:
  boot-loader FW version:        255
  firmware version:              5.44
  hardware version:              1
Serial number:                   00:b0:00:00:64:aa
Device ID:                       JTAGICEmkII
avrdude: jtagmkII_getsync(): Using a 298-byte device descriptor
avrdude: jtagmkII_setparm()
avrdude: jtagmkII_setparm(): Sending set parameter command (parm 0x03, 1 
bytes): 0x80 (1 bytes msg)
avrdude: jtagmkII_getsync(): Sending get sync command: 0x80 (1 bytes msg)
         AVR Part                      : ATXMEGA128A1
         Chip Erase delay              : 0 us
         PAGEL                         : P00
         BS2                           : P00
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 0
         StabDelay                     : 0
         CmdexeDelay                   : 0
         SyncLoops                     : 0
         ByteDelay                     : 0
         PollIndex                     : 0
         PollValue                     : 0x00
         Memory Detail                 :

                                  Block Poll               Page                 
      
Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  
MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- 
----- ---------
           eeprom         0     0     0    0 no       2048   32      0     0    
 
0 0x00 0x00
           flash          0     0     0    0 no     131072  512      0     0    
 
0 0x00 0x00
           boot           0     0     0    0 no       8192  512      0     0    
 
0 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0    
 
0 0x00 0x00
           fuse0          0     0     0    0 no          1    0      0     0    
 
0 0x00 0x00
           fuse1          0     0     0    0 no          1    0      0     0    
 
0 0x00 0x00
           fuse2          0     0     0    0 no          1    0      0     0    
 
0 0x00 0x00
           fuse4          0     0     0    0 no          1    0      0     0    
 
0 0x00 0x00
           fuse5          0     0     0    0 no          1    0      0     0    
 
0 0x00 0x00
           lockbits       0     0     0    0 no          1    0      0     0    
 
0 0x00 0x00
           calibration    0     0     0    0 no        512    0      0     0    
 
0 0x00 0x00
           usersig        0     0     0    0 no        512    0      0     0    
 
0 0x00 0x00

         Programmer Type : JTAGMKII
         Description     : Atmel JTAG ICE mkII
avrdude: jtagmkII_getparm()
avrdude: jtagmkII_getparm(): Sending get parameter command (parm 0x01): 0x81 
(3 bytes msg)
avrdude: jtagmkII_getparm()
avrdude: jtagmkII_getparm(): Sending get parameter command (parm 0x02): 0x81 
(5 bytes msg)
         M_MCU hardware version: 0
         M_MCU firmware version: 5.44
         S_MCU hardware version: 1
         S_MCU firmware version: 5.44
         Serial number:          00:b0:00:00:64:aa
avrdude: jtagmkII_getparm()
avrdude: jtagmkII_getparm(): Sending get parameter command (parm 0x06): 0x81 
(3 bytes msg)
         Vtarget         : 3.4 V
avrdude: jtagmkII_getparm()
avrdude: jtagmkII_getparm(): Sending get parameter command (parm 0x07): 0x81 
(2 bytes msg)
         JTAG clock      : 891.7 kHz (1.1 us)

avrdude: jtagmkII_setparm()
avrdude: jtagmkII_setparm(): Sending set parameter command (parm 0x1b, 4 
bytes): 0x80 (1 bytes msg)
avrdude: jtagmkII_set_devdescr(): Sending set device descriptor command: 0x80 
(1 bytes msg)
avrdude: jtagmkII_getsync(): Sending sign-on command: 0x86 (28 bytes msg)
JTAG ICE mkII sign-on message:
Communications protocol version: 1
M_MCU:
  boot-loader FW version:        255
  firmware version:              5.44
  hardware version:              0
S_MCU:
  boot-loader FW version:        255
  firmware version:              5.44
  hardware version:              1
Serial number:                   00:b0:00:00:64:aa
Device ID:                       JTAGICEmkII
avrdude: jtagmkII_getsync(): Using a 298-byte device descriptor
avrdude: jtagmkII_setparm()
avrdude: jtagmkII_setparm(): Sending set parameter command (parm 0x03, 1 
bytes): 0x80 (1 bytes msg)
avrdude: jtagmkII_getsync(): Sending get sync command: 0x80 (1 bytes msg)
avrdude: jtagmkII_reset(): Sending reset command: 0x80 (1 bytes msg)
avrdude: jtagmkII_read_byte(.., hfuse, 0x1, ...)
avrdude: jtagmkII_program_enable(): Sending enter progmode command: 0x80 (1 
bytes msg)
avrdude: jtagmkII_read_byte(): Sending read memory command: 0x82 (2 bytes msg)
avrdude: AVR device initialized and ready to accept instructions

Reading |                                                    | 0% 
0.00savrdude: jtagmkII_read_byte(.., signature, 0x0, ...)
avrdude: jtagmkII_read_byte(): Sending read memory command: 0x82 (2 bytes msg)
avrdude: jtagmkII_read_byte(.., signature, 0x1, ...)
avrdude: jtagmkII_read_byte(): Sending read memory command: 0x82 (2 bytes msg)
Reading | #################                                  | 33% 
0.01savrdude: jtagmkII_read_byte(.., signature, 0x2, ...)
avrdude: jtagmkII_read_byte(): Sending read memory command: 0x82 (2 bytes msg)
Reading | ################################################## | 100% 0.01s

avrdude: Device signature = 0x000000
avrdude: Yikes!  Invalid device signature.
         Double check connections and try again, or use -F to override
         this check.

avrdude: jtagmkII_program_disable(): Sending leave progmode command: 0x80 (1 
bytes msg)
avrdude: jtagmkII_reset(): Sending reset command: 0x80 (1 bytes msg)
avrdude: jtagmkII_close()
avrdude: jtagmkII_close(): Sending GO command: 0x80 (1 bytes msg)
avrdude: jtagmkII_close(): Sending sign-off command: 0x80 (1 bytes msg)

avrdude done.  Thank you.