freeipmi-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[Freeipmi-devel] support for sensors of IBM Server System x3850 X5


From: Werner Fischer
Subject: [Freeipmi-devel] support for sensors of IBM Server System x3850 X5
Date: Fri, 15 Jun 2012 11:39:44 +0200

Hi Al,

Kurt - a user of the IPMI plugin for Nagios/Icinga - reported on our
mailing list that an supposed critical event ('transition to Critical
from less severe') does not cause a warning through our plugin.

Reason is that the reported sensor state is "N/A" so I think that
FreeIPMI cannot interpret it's state:
  ID  | Name           | Type           | State | Reading | Units | Event
  387 | Ext QPI Link 2 | Slot/Connector | N/A   | N/A     | N/A   | 'transition 
to Critical from less severe'

There are also some other sensors, which report events, but are not
recognized by FreeIPMI widely enough so FreeIPMI could give a State
information (state is N/A):
        22  | Scale Config     | Version Change              | N/A      | N/A   
     | N/A   | 'OK'
        [...]
        66  | VT Fault         | Chassis                     | N/A      | N/A   
     | N/A   | 'OK'
        [...]
        386 | Ext QPI Link 1   | Slot/Connector              | N/A      | N/A   
     | N/A   | 'OK'
        387 | Ext QPI Link 2   | Slot/Connector              | N/A      | N/A   
     | N/A   | 'transition to Critical from less severe'
        388 | Ext QPI Link 3   | Slot/Connector              | N/A      | N/A   
     | N/A   | 'OK'
        389 | Ext QPI Link 4   | Slot/Connector              | N/A      | N/A   
     | N/A   | 'OK'
        390 | CPU 1 Int Link   | Cable/Interconnect          | N/A      | N/A   
     | N/A   | 'OK'
        391 | CPU 2 Int Link   | Cable/Interconnect          | N/A      | N/A   
     | N/A   | 'OK'
        392 | CPU 3 Int Link   | Cable/Interconnect          | N/A      | N/A   
     | N/A   | 'OK'
        393 | CPU 4 Int Link   | Cable/Interconnect          | N/A      | N/A   
     | N/A   | 'OK'
        394 | Scaling Failed   | Boot Error                  | N/A      | N/A   
     | N/A   | 'OK'
        395 | Lane Failover 1  | Memory                      | N/A      | N/A   
     | N/A   | 'OK'
        396 | MemSpareErr1     | Memory                      | N/A      | N/A   
     | N/A   | 'OK'
        397 | MemSpareErr2     | Memory                      | N/A      | N/A   
     | N/A   | 'OK'
        398 | MemSpareErr3     | Memory                      | N/A      | N/A   
     | N/A   | 'OK'
        399 | MemSpareErr4     | Memory                      | N/A      | N/A   
     | N/A   | 'OK'
        400 | MemSpareErr5     | Memory                      | N/A      | N/A   
     | N/A   | 'OK'
        401 | MemSpareErr6     | Memory                      | N/A      | N/A   
     | N/A   | 'OK'
        402 | MemSpareErr7     | Memory                      | N/A      | N/A   
     | N/A   | 'OK'
        403 | MemSpareErr8     | Memory                      | N/A      | N/A   
     | N/A   | 'OK'
        404 | Lane Failover 2  | Memory                      | N/A      | N/A   
     | N/A   | 'OK'
        405 | Lane Failover 3  | Memory                      | N/A      | N/A   
     | N/A   | 'OK'
        406 | Lane Failover 4  | Memory                      | N/A      | N/A   
     | N/A   | 'OK'
        407 | Lane Failover 5  | Memory                      | N/A      | N/A   
     | N/A   | 'OK'
        408 | Lane Failover 6  | Memory                      | N/A      | N/A   
     | N/A   | 'OK'
        409 | Lane Failover 7  | Memory                      | N/A      | N/A   
     | N/A   | 'OK'
        410 | Lane Failover 8  | Memory                      | N/A      | N/A   
     | N/A   | 'OK'
        [...]
        426 | FPGA FW Mismatch | Version Change              | N/A      | N/A   
     | N/A   | 'OK'
        427 | TPM Phys Pres    | Button/Switch               | N/A      | N/A   
     | N/A   | 'OK'
        [...]
        429 | No I/O Resources | System Firmware Progress    | N/A      | N/A   
     | N/A   | 'OK'
        430 | Memory Resize    | POST Memory Resize          | N/A      | N/A   
     | N/A   | 'OK'
        [...]
        433 | IMM FW Failover  | Version Change              | N/A      | N/A   
     | N/A   | 'OK'

Are there chances that you could add support for those sensors to future
FreeIPMI versions?

You can get verbose output in the following posting (scroll down to the
end)
http://lists.thomas-krenn.com/pipermail/ipmi-plugin-user/2012-June/000182.html

I have put Kurt on CC and asked him to subscribe to
address@hidden so he can get in touch with you directly, too.

Best regards,
Werner

-- 
: Werner Fischer
: Technology Specialist
: Thomas-Krenn.AG | The server-experts
: http://www.thomas-krenn.com | http://www.thomas-krenn.com/wiki




reply via email to

[Prev in Thread] Current Thread [Next in Thread]