[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Freeipmi-users] Power statistics for Supermicro A+ 1023US-TR4 serve
From: |
Vladimir Stegailov |
Subject: |
Re: [Freeipmi-users] Power statistics for Supermicro A+ 1023US-TR4 server |
Date: |
Wed, 25 Jul 2018 11:48:53 +0300 |
Hi Al,
thank you for the response!
Do you think that this problem is a flaw in the DCMI implementation of the
current motherboard firmware?
In this case, we could hope it is to be corrected in future versions.
Or is it rather a policy of the vendor? It seems so since they don’t
provide the raw command for PSU monitoring.
Are we to abandon plans for using freeipmi-based accounting in SLURM for
this cluster?
Vlad
On Tue, Jul 24, 2018 at 10:37 PM, Albert Chu <address@hidden> wrote:
> Hi Vladimir,
>
> > What could be the reason for this problem with FreeIPMI inability to
> > read power statistics?
>
> Internally, I don't know how Supermicro is obtaining the data they have
> in their output. It would not be surprising if it were via an OEM
> specific extension. It would also not be surprising the motherboard
> does not support as much DCMI as they advertise.
>
> I have seen some motherboards that allow some mechanisms (such as DCMI)
> via LAN but not via in-band. Perhaps it would be worthwhile trying --
> get-system-power-statistics over LAN?
>
> Al
>
>
> On Tue, 2018-07-24 at 12:44 +0300, Vladimir Stegailov wrote:
> > Hi!
> >
> > I have a question concerning FreeIPMI usage on the novel Supermicro
> > A+
> > Server 1023US-TR4 with two AMD Epyc CPUs.
> >
> > The BMC firmware of the corresponding H11DSU-iN motherboard has been
> > upgraded to the latest available version (1.30).
> >
> > The FreeIPMI test shows that the power monitoring is available:
> >
> > *host1:~ # ipmi-dcmi --get-dcmi-capability-info*
> > *DCMI Specification Conformance : 1.1*
> >
> > *Power Management / Monitoring Support : Available*
> > *In-band System Interface Channel : Available*
> > *Serial TMODE : Not present*
> > *Out-Of-Band Secondary LAN Channel : Not present*
> >
> > *Number of SEL entries : 512*
> > *Record Level SEL Flush upon Rollover : Not present*
> > *Entire SEL Flush upon Rollover : Not present*
> > *SEL automatic rollover : Not present*
> > *DHCP Host Name : Not present*
> > *Asset Tag : Available*
> >
> > *Power Management Device Slave Address : 10h*
> > *Power Management Controller Device Revision : 1*
> > *Power Management Controller Channel Number : 0*
> >
> > *Primary LAN Out-of-band Channel Number : 1*
> > *Secondary LAN Out-of-band Channel Number : Not supported*
> > *Serial Out-of-band TMODE Capability Channel Number : Not supported*
> >
> > *ipmi_cmd_dcmi_get_dcmi_capability_info_enhanced_system_power_statist
> > ics_attributes:
> > bad completion code*
> >
> > However it is not possible to get power statistics by a DCMI request
> > (it
> > stops with an error):
> >
> > *host1:~ # ipmi-dcmi --debug --get-system-power-statistic*
> > *=====================================================*
> > *Group Extension - Get Power Reading Request*
> > *=====================================================*
> > *[ 2h] = cmd[ 8b]*
> > *[ DCh] = group_extension_identification[ 8b]*
> > *[ 1h] = mode[ 8b]*
> > *[ 0h] = mode_attributes[ 8b]*
> > *[ 0h] = reserved[ 8b]*
> > *=====================================================*
> > *Group Extension - Get Power Reading Response*
> > *=====================================================*
> > *[ 2h] = cmd[ 8b]*
> > *[ FFh] = comp_code[ 8b]*
> > *ipmi_cmd_dcmi_get_power_reading: bad completion code*
> >
> > At the same time, the Supermicro tool does show power statistics:
> >
> > address@hidden:~/repos/SMCIPMITool_2.20.0_build.180525_bundleJRE_L
> > inux>
> > ./SMCIPMITool ipmi1 ADMIN ADMIN pminfo*
> > * [SlaveAddress = B0h] [Module 1]*
> > * Item | Value *
> > * ---- | ----- *
> > * Status | ON (00 00) *
> > * Input Voltage | 225.75 V *
> > * Input Current | 0.8 A *
> > * Main Output Voltage | 12.16 V *
> > * Main Output Current | 13.82 A *
> > * Temperature 1 | 31C/88F *
> > * Temperature 2 | 38C/100F *
> > * Fan 1 | 2624 RPM *
> > * Fan 2 | 0 RPM *
> > * Main Output Power | 168 W *
> > * Input Power | 176 W *
> > * PMBus Revision | 0x22 *
> > * PWS Serial Number | P1K0ACH21AN0368 *
> > * PWS Module Number | PWS-1K02A-1R *
> > * PWS Revision | 1.2 *
> >
> > What could be the reason for this problem with FreeIPMI inability to
> > read
> > power statistics?
> > (Unfortunately, we are not able to get any help from Supermicro with
> > this
> > issue.)
> >
> > Thank you.
> >
> > Vlad
> > _______________________________________________
> > Freeipmi-users mailing list
> > address@hidden
> > https://lists.gnu.org/mailman/listinfo/freeipmi-users
> --
> Albert Chu
> address@hidden
> Computer Scientist
> High Performance Systems Division
> Lawrence Livermore National Laboratory
>
>