5110 or 6310

[Jean-Marc Acke]

Hi,

 

i've used the gnokii-pre20 with a Nokia 5110. At some points it works.  The only part that does not work is sending sms messages.

 

For the moment I'm testing with a Nokia 6310 and a DLR-3P cable from Nokia.

 

This is my config file :

 

[global]

 

# Set port to the physical serial port used to connect to your phone
port = /dev/ttyS0

 

# Set model to the model number of your phone
model = 6310

 

# Initlength controls the number of characters sent to the
# phone during initialisation.  You can either set it to
# the word "default" or a positive integer.
#
# You can try setting this value if you want to connect
# to the phone quicker.  If you've never noticed the
# connection to be slow, it is suggested that you
# leave this alone.  Read the initialisation code in fbus-xxxx
# to understand what this changes if you're curious.
initlength = default

 

# The type of the connection, for IR set this to infrared or irda.
# If you have 6210/6250/7110 phone and dau9p cable (the one you can
# use with 6100 series and cannot use hardware modem from the phone)
# you may want to use 'dau9p' value to get faster initialization.
connection = serial

 

# Set bindir to point to the location of the various gnokii binaries.
# In particular ensure that mgnokiidev is in this location, with
# permissions 4750, owned by root, group gnokii.  Ensure you
# are in the gnokii group and that the group exists...
bindir = /usr/local/sbin/

 

# Set this to 'yes' if you want gnokii to set and check the lock file in
# /var/lock directory. It avoids potential conflicts with other serial
# port software (eg. minicom). If you have wrong permissions for the
# directory, a warning will be generated. If you don't want a lockfile, set
# it to 'no'.
use_locking = yes

 

# Baudrate to use on serial port connections.
# Currently used only by models AT and BIP/CIMD. Defaults to 19200.
#serial_baudrate = 19200

 

# Force waiting after each send character the specified usec time.
# Value -1 forces the fastest 'block' writing,
# value 0 writes each character separately without any explicite waiting,
# other positive values specify the appropriate 1/1000000 sec delaying.
# Siemens M20 requires at least "1"!  FIXME: Model-driven autodetection
serial_write_usleep = 10000

 

# Force serial port handshaking mode, useful primarily for "AT" model.
# Gnokii "AT" model uses software handshake by default.
# Possible values: hardware (RTS/CTS - 7 wires) or software (XON/XOFF - 3 wires)
handshake =  hardware

 

# If defined (not commented out by '#') it will quit Gnokii anytime
# when DCD line will drop.
#require_dcd = 1

 

# Run the specified script(s) right after opening and initializing the device
# and before any communucation (right before closing for disconnect_script).
# You may find handy to use it to connect your modem to SMS Center
# when using BIP or CIMD protocols
# Non-absolute path is relative to the specific directory where gnokii is run!
#connect_script =/usr/src/gnokii-0.4.0pre19/Docs/sample/cimd-connect
#disconnect_script =

 

# Any entries in the following two sections will be set as environment
# variables when running the scripts.
# Handy for use for $VAR substitutions in your chat(8) script.
#[connect_script]

 

#TELEPHONE = 12345678
#[disconnect_script]

 

When I run : any gnokii-command i get the following error :

 

GNOKII Version 0.4.0pre20
Opened configuration file /root/.gnokiirc
Added new section global
Adding key/value port//dev/ttyS0
Adding key/value model/6310
Adding key/value initlength/default
Adding key/value connection/serial
Adding key/value bindir//usr/local/sbin/
Adding key/value use_locking/yes
Adding key/value serial_write_usleep/10000
Adding key/value handshake/hardware
Lockfile /var/lock/LCK..ttyS0 is stale. Overriding it..
Connecting
Serial device: opening device /dev/ttyS0
Serial device: setting speed to 115200
Serial device: setting RTS to low and DTR to low
Getting model...
Message sent: 0x1b / 0x0006
00 01 00 07 01 00                               |                
SM_Block Retry - 0
Message sent: 0x1b / 0x0006
00 01 00 07 01 00                               |                
SM_Block Retry - 1
Message sent: 0x1b / 0x0006
00 01 00 07 01 00                               |                
SM_Block Retry - 2
Serial device: opening device /dev/ttyS0
Serial device: setting speed to 115200
Serial device: setting RTS to low and DTR to high
Getting model...
Message sent: 0x1b / 0x0006
00 01 00 07 01 00                               |                
SM_Block Retry - 0
Message sent: 0x1b / 0x0006
00 01 00 07 01 00                               |                
SM_Block Retry - 1
Message sent: 0x1b / 0x0006
00 01 00 07 01 00                               |                
SM_Block Retry - 2
Telephone interface init failed! Quitting.
serial_close_all() executed

 

When I change the model into AT, it works ...

 

Any clues ?

 

JM