gnokii-users
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

6310 sending sms errors


From: saidane ahmed
Subject: 6310 sending sms errors
Date: Sat, 3 Dec 2005 20:29:03 +0100 (CET)

(sorry for my bad english i am from algeria)
hi,
i can't send sms with my nokia 6310 i use gnokii-0.6.10
when i tape the commande:
address@hidden root]# smsd -m file -c /usr/local/cache/smsd
 
i have:
General Data Coding
dcs: 0x0
Length: 0x0
user_data_length: 0x0
ValidityIndicator: 2
user_data:
Sending
Sending SMS...(54)
Message sent: 0x02 / 0x0036
00 01 00 02 00 00 00 55 55 01 02 2c 11 00 00 00 | UU ,
00 04 82 0c 01 08 0b 81 f3 ff f9 ff 31 f8 82 0c | 1
02 08 07 91 12 73 00 84 75 f1 80 08 00 00 55 55 | s u UU
55 55 08 04 01 a9 | UU
SM_Block: exiting the retry loop
Event 0 failed with return code 11!
Getting SMS Folder (2) status (2)...
Special case IN/OUTBOX in GetSMSFolderStatus!
Message sent: 0x14 / 0x000a
00 01 00 0c 02 02 0f 55 55 55 | UUU
SM_Block: exiting the retry loop
Message sent: 0x14 / 0x000a
00 01 00 0c 02 02 0f 55 55 55 | UUU
SM_Block: exiting the retry loop
Message sent: 0x14 / 0x000a
00 01 00 0c 02 02 0f 55 55 55 | UUU
SM_Block: exiting the retry loop
GN_OP_GetSMSFolderStatus at line 402 in file lowlevel.c returns error 11
Entering dumb mode.Getting SMS...
Getting SMS Folders...
Message sent: 0x14 / 0x0006
00 01 00 12 00 00 |
SM_Block: exiting the retry loop
Message sent: 0x14 / 0x0006
00 01 00 12 00 00 |
SM_Block: exiting the retry loop
Message sent: 0x14 / 0x0006
00 01 00 12 00 00 |
SM_Block: exiting the retry loop
Getting SMS...
Getting SMS Folders...
Message sent: 0x14 / 0x0006
00 01 00 12 00 00 |
SM_Block: exiting the retry loop
Message sent: 0x14 / 0x0006
00 01 00 12 00 00 |
SM_Block: exiting the retry loop
Message sent: 0x14 / 0x0006
00 01 00 12 00 00 |
SM_Block: exiting the retry loop
Getting SMS...
Getting SMS Folders...
Message sent: 0x14 / 0x0006
00 01 00 12 00 00 |
SM_Block: exiting the retry loop
Message sent: 0x14 / 0x0006
00 01 00 12 00 00 |
SM_Block: exiting the retry loop
Message sent: 0x14 / 0x0006
00 01 00 12 00 00 |
SM_Block: exiting the retry loop
Getting SMS...
Getting SMS Folders...
Message sent: 0x14 / 0x0006
00 01 00 12 00 00 |
SM_Block: exiting the retry loop
Message sent: 0x14 / 0x0006
00 01 00 12 00 00 |
SM_Block: exiting the retry loop
Message sent: 0x14 / 0x0006
00 01 00 12 00 00 |
SM_Block: exiting the retry loop
Getting SMS...
Getting SMS Folders...
Message sent: 0x14 / 0x0006
00 01 00 12 00 00 |
SM_Block: exiting the retry loop
Message sent: 0x14 / 0x0006
00 01 00 12 00 00 |
SM_Block: exiting the retry loop
Message sent: 0x14 / 0x0006
00 01 00 12 00 00 |
SM_Block: exiting the retry loop
Getting SMS...
Getting SMS Folders...
Message sent: 0x14 / 0x0006
00 01 00 12 00 00 |
SM_Block: exiting the retry loop
Message sent: 0x14 / 0x0006
00 01 00 12 00 00 |
SM_Block: exiting the retry loop
 
in the directory /usr/local/cache/smsd there are the file out.1 who content:
070861786
test gateway
 
my gnokiirc is:
[global]
# Set port to the physical port used to connect to your phone.
# Linux version is:
port = /dev/ttyS0
#
# For MacOSX you will need something like:
# port = /dev/cu.USA28X1P1.1
#
# For Win32 you want to use:
# port = com1:
# or similiar.
#
# FreeBSD (probably NetBSD and OpenBSD too) use:
# port = /dev/cuaa0
#
# With Linux-IrDA you will want to use
# port = /dev/ircomm0
# or similiar.
#
# Use this setting also for the Bluetooth connection:
# port = aa:bb:cc:dd:ee:ff
# when using it with AT driver set it to:
# port = /dev/rfcomm0
# or similiar.
#
# For the Linux USB cables you will need one of the following settings (or
# similiar)
# port = /dev/ttyUSB0
# port = /dev/tts/USB0
# port = /dev/ttyACM0
# the last one will work only with AT driver. The correct setting should be
# given in the dmesg output.
# Set model to the model number of your phone. For the
# Symbian phones use:
# model = series60
# For other non-Nokia phones and when you want to use AT
# mode use:
# model = AT
# If you can't figure out what to put here read the FAQ.
# If it still doesn't help, consult gnokii-ml or #gnokii at freenode.
model = 6310
# There are few main models that should make use of the certain drivers.
# These are: 6110, 7110, 6510, 3110, 2110, 6160.
# Initlength controls the number of characters sent to the
# phone during initialisation. You can either set it to
# the word "default" or a positive integer.
#
# You can try setting this value if you want to connect
# to the phone quicker. If you've never noticed the
# connection to be slow, it is suggested that you
# leave this alone. Read the initialisation code in fbus-xxxx
# to understand what this changes if you're curious.
initlength = default
# The type of the connection, for IR set this to infrared or irda.
# For the nk6110 driver only infrared is valid for the IrDA connection.
# See Docs/gnokii-ir-howto for more detailes on this.
# If you have 6210/6250/7110 phone and dau9p cable (the one you can
# use with 6100 series and cannot use hardware modem from the phone)
# you may want to use 'dau9p' value to get faster initialization.
# If you use dlr3 or dlr3p cable for nokia phones in FBUS mode (ie.
# you don't use model = AT) you may want to use 'dlr3p' value here.
# Note that it is recommended and currently the best way to use this
# cable with nk6510 driver.
#connection = serial
# With DKU-2 cable use the following setting
# connection = dku2
# With DKU-5 cable use the following setting
connection = dlr3p
# For Bluetooth and AT driver use the following setting
# connection = serial
# For other Bluetooth settings use
# connection = bluetooth
# For infraded connection with phones other then Nokia 6110/6130/6150 use
# connection = irda
# Set this to 'yes' if you want gnokii to set and check the lock file in
# /var/lock directory. It avoids potential conflicts with other serial
# port software (eg. minicom). If you have wrong permissions for the
# directory, a warning will be generated. If you don't want a lockfile, set
# it to 'no'.
use_locking = yes
# Baudrate to use on serial port connections.
# Currently used only by models AT and BIP/CIMD. Defaults to 19200.
serial_baudrate = 19200
# Force waiting after each send character the specified usec time.
# Value -1 forces the fastest 'block' writing,
# value 0 writes each character separately without any explicite waiting,
# other positive values specify the appropriate 1/1000000 sec delaying.
# Siemens M20 requires at least "1"! FIXME: Model-driven autodetection
#serial_write_usleep = 1
# Force serial port handshaking mode, useful primarily for "AT" model.
# Gnokii "AT" model uses software handshake by default.
# Possible values: hardware (RTS/CTS - 7 wires) or software (XON/XOFF - 3 wires)
#handshake = software
# If defined (not commented out by '#') it will quit Gnokii anytime
# when DCD line will drop.
#require_dcd = 1
# If you are using a bluetooth connection, you can specify the rfcomm
# channel number here. Default value is 1.
#rfcomm_channel = 1
# There may happen various timeouts during the communication with the phone.
# This parameter enables the retransmission policy. Ie. if the phone doesn't
# respond, we send the frame again. This happend mainly with the older
# phones. You may want to enable it when you see mysterious timeouts.
# Be very carefull with this option. It is suspected to cause phone breakage
# with new DCT4 phones (like Nokia 6100). By default it is switched off
# (sm_retry = 0)
#sm_retry = 1
# Run the specified script(s) right after opening and initializing the device
# and before any communucation (right before closing for disconnect_script).
# You may find handy to use it to connect your modem to SMS Center
# when using BIP or CIMD protocols
# Non-absolute path is relative to the specific directory where gnokii is run!
#connect_script = /absolute/path/to/gnokii/Docs/sample/cimd-connect
#disconnect_script =
# When sending SMS you can experience timeouts. This is the feature of the
# overloaded SMSCs. The phones waits for the response from the SMSC confirming
# that it received the short message. When the SMSC is DoSed with many requests
# it will take more time to get the response. Adjust it to your needs. The
# value is given in seconds to wait. Defaults to 10 seconds. Set to 0 to wait
# forever.
smsc_timeout = 20
# Set bindir to point to the location of the various gnokiid binaries.
# In particular ensure that mgnokiidev is in this location, with
# permissions 4750, owned by root, group gnokii. Ensure you
# are in the gnokii group and that the group exists...
[gnokiid]
bindir = /usr/local/sbin/
# Any entries in the following two sections will be set as environment
# variables when running the scripts.
# Handy for use for $VAR substitutions in your chat(8) script.
[connect_script]
TELEPHONE = 12345678
[disconnect_script]
 
# The following parameters control how libgnokii handle the debugging messages.
# Currently there are three categories: "debug" controls the libgnokii
# normal debug output, "rlpdebug" controls the debug output of the RLP
# subsystem, and "xdebug" is used by the xgnokii or smsd.
[logging]
# where to log the debug output (on: stderr, off: /dev/null)
debug = on
# where to log the rlp debug output (on: stderr, off: /dev/null)
rlpdebug = off
# where to log X debug output (on: stderr, off: /dev/null)
xdebug = off


Appel audio GRATUIT partout dans le monde avec le nouveau Yahoo! Messenger
Téléchargez le ici !
reply via email to

[Prev in Thread] Current Thread [Next in Thread]