Re: [Fwd: Gnokii --identify with Nokia 6280 not work]

[Bardok]

Hello,

i change the config file to use USB but that's won't work :

address@hidden:~$ xgnokii --identify
LOG: debug mask is 0x1
Config read from file /home/chris/.gnokiirc.

(xgnokii:14181): Gtk-WARNING **: horizontal scrolling not implemented

(xgnokii:14181): Gtk-WARNING **: horizontal scrolling not implemented
phone instance config:
model: 6510
port_device: /dev/ttyACM0
connection_type: 9
init_length: 0
serial_baudrate: 19200
serial_write_usleep: -1
hardware_handshake: 0
require_dcd: 0
smsc_timeout: 100
connect_script:
disconnect_script:
rfcomm_cn: 1
sm_retry: off
Connecting
Serial device: opening device /dev/ttyACM0
Getting model...
Message sent: 0x1b / 0x0006
00 01 00 07 01 00                               |                
The fbus stream is out of sync - expected 0x0c, got 0x00
The fbus stream is out of sync - expected 0x0c, got 0x00
Message sent: 0x1b / 0x0006
00 01 00 07 01 00                               |                
The fbus stream is out of sync - expected 0x0c, got 0x00
The fbus stream is out of sync - expected 0x0c, got 0x00
Message sent: 0x1b / 0x0006
00 01 00 07 01 00                               |                
The fbus stream is out of sync - expected 0x0c, got 0x00
The fbus stream is out of sync - expected 0x0c, got 0x00
Serial device: closing device
Telephone interface init failed: Command timed out.
Quitting.
Failed to open the phone. Quitting.
Serial device: closing device

My dmesg :

[199388.962946] usb 3-2: new full speed USB device using uhci_hcd and address 12
[199389.140116] usb 3-2: configuration #1 chosen from 1 choice
[199389.197069] drivers/usb/class/cdc-acm.c: Ignoring extra header, type -3, length 4
[199389.197084] cdc_acm 3-2:1.1: ttyACM0: USB ACM device
[199389.298366] usb 3-2: device_add(3-2:1.9) --> -110
[199389.729511] usb 3-2: USB disconnect, address 12
[199393.304720] usb 3-2: new full speed USB device using uhci_hcd and address 13
[199393.390660] usb 3-2: configuration #1 chosen from 1 choice
[199411.429537] usb 3-2: USB disconnect, address 13
[199411.802821] usb 3-2: new full speed USB device using uhci_hcd and address 14
[199411.895452] usb 3-2: configuration #1 chosen from 1 choice
[199411.925574] drivers/usb/class/cdc-acm.c: Ignoring extra header, type -3, length 4
[199411.925585] cdc_acm 3-2:1.1: ttyACM0: USB ACM device
[199412.000480] usb 3-2: device_add(3-2:1.9) --> -110

My lsusb :

address@hidden:~$ lsusb
Bus 005 Device 002: ID 04b4:6830 Cypress Semiconductor Corp. USB-2.0 IDE Adapter
Bus 005 Device 001: ID 0000:0000 
Bus 004 Device 001: ID 0000:0000 
Bus 003 Device 014: ID 0421:045a Nokia Mobile Phones
Bus 003 Device 001: ID 0000:0000 
Bus 002 Device 005: ID 046d:c001 Logitech, Inc. N48/M-BB48 [FirstMouse Plus]
Bus 002 Device 004: ID 046d:08f6 Logitech, Inc.
Bus 002 Device 001: ID 0000:0000 
Bus 001 Device 001: ID 0000:0000 
address@hidden:~$

I try to change connection type dku2 or dku2libusb, none of them work.

Thanks for your help.

Bardok.

hacknslash a écrit :

	Hello Bardok

You seem to be using a usb cable, but your config file is trying to
connect to the serial port.

In a terminal please type 

dmesg


and then


lsusb

please look for ttyusb0 or ttyACM0

Regards
Ian
  

---

Sujet:

Gnokii --identify with Nokia 6280 not work

Expéditeur:

Bardok <address@hidden>

Date:

Sun, 13 May 2007 19:24:31 +0200

Destinataire:

address@hidden

Destinataire:

address@hidden

Hello,

my phone is a nokia 6280 with a cable CA-53.

I'm using gnokii 0.6.16

Thanks for your great works.

Bye.

GNOKII Version 0.6.16
LOG: debug mask is 0x1
Config read from file /home/chris/.gnokiirc.
phone instance config:
model: 6510
port_device: /dev/ttyS0
connection_type: 0
init_length: 0
serial_baudrate: 19200
serial_write_usleep: -1
hardware_handshake: 0
require_dcd: 0
smsc_timeout: 100
connect_script: 
disconnect_script: 
rfcomm_cn: 1
sm_retry: off
Connecting
Serial device: opening device /dev/ttyS0
Serial device: setting speed to 115200
Serial device: setting RTS to low and DTR to low
Getting model...
Message sent: 0x1b / 0x0006
00 01 00 07 01 00                               |                 
SM_Block: exiting the retry loop
Message sent: 0x1b / 0x0006
00 01 00 07 01 00                               |                 
SM_Block: exiting the retry loop
Message sent: 0x1b / 0x0006
00 01 00 07 01 00                               |                 
SM_Block: exiting the retry loop
Serial device: closing device
Serial device: opening device /dev/ttyS0
Serial device: setting speed to 115200
Serial device: setting RTS to low and DTR to high
Getting model...
Message sent: 0x1b / 0x0006
00 01 00 07 01 00                               |                 
SM_Block: exiting the retry loop
Message sent: 0x1b / 0x0006
00 01 00 07 01 00                               |                 
SM_Block: exiting the retry loop
Message sent: 0x1b / 0x0006
00 01 00 07 01 00                               |                 
SM_Block: exiting the retry loop
Serial device: closing device
Serial device: opening device /dev/ttyS0
Serial device: setting RTS to low and DTR to low
Serial device: setting RTS to high and DTR to high
Serial device: setting speed to 19200
Switching to FBUS mode
Serial device: setting speed to 115200
Getting model...
Message sent: 0x1b / 0x0006
00 01 00 07 01 00                               |                 
SM_Block: exiting the retry loop
Message sent: 0x1b / 0x0006
00 01 00 07 01 00                               |                 
SM_Block: exiting the retry loop
Message sent: 0x1b / 0x0006
00 01 00 07 01 00                               |                 
SM_Block: exiting the retry loop
Serial device: closing device
Telephone interface init failed: Command timed out.
Quitting.
Command timed out.
Serial device: closing device

  

_______________________________________________
gnokii-users mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/gnokii-users