Re: [Paparazzi-devel] Stuck at Holding Point Block

[Luiz Flavio Felizardo]

Oh I see, just tested it and u are right. Cant change anything in my settings tab.

Do you happen to have a hyperlink to the solution pleaseee? 

And thanks very much!

On Sun, Aug 12, 2012 at 4:34 PM, AJ Kochevar <address@hidden> wrote:

I said uplink.  Not downlink.  The gcs wouldn't even populate if you didn't have a downlink.

On Aug 12, 2012 12:31 PM, "Luiz Flavio Felizardo" <address@hidden> wrote:

I dont think link is the problem,

I ve used    ivyprobe '(.*)'   command on my terminal and I have plenty of messages comming and going, follow some examples:

Paparazzi server sent  'ground WAYPOINT_MOVED 15 10 -22.414307 -45.448538 75.000000'

Paparazzi server sent  'ground WAYPOINT_MOVED 15 11 -22.414096 -45.449770 75.000000'

Paparazzi server sent  'ground WAYPOINT_MOVED 15 12 -22.412289 -45.449764 75.000000'

Paparazzi server sent  'ground WAYPOINT_MOVED 15 13 -22.412294 -45.447821 75.000000'

Paparazzi server sent  'ground WAYPOINT_MOVED 15 14 -22.414101 -45.447827 75.000000'

Paparazzi server sent  'ground TELEMETRY_STATUS 15 0.015192'

Link sent  '15 GPS 0 612502016 0 0 -17000 0 0 0 218500 23 4'

Link sent  '15 WP_MOVED 6 453658.406250 -2478651.500000 75.000000 23'

Link sent  '15 BAT 0 124 0 0 1 218 0 0'

Link sent  '15 IMU_GYRO 0.008301 0.001953 -0.013672'

Link sent  '15 CALIBRATION 0.0 0'

Link sent  '15 PPM 0 0,0,0,0,0,0,0,0'

Link sent  '15 NAVIGATION 0 2 5671210.0 2478732.0 0.0 38306737815552.0 0 0'

Link sent  '15 GPS 0 612502016 0 0 -17000 0 0 0 218750 23 5'

On Sun, Aug 12, 2012 at 4:18 PM, AJ Kochevar <address@hidden> wrote:

Can you change a setting in the settings page, like a gain or something?  If not then it means you dont have an uplink.  Common problem, and solutions are outlined in the wiki and in this mailing list.  If so... then I dont know!

AJ

On Sun, Aug 12, 2012 at 12:12 PM, Luiz Flavio Felizardo <address@hidden> wrote:

Hello everyone! 

Does anybody have an idea why am I stuck at Holding Point Block? cant select the takeoff block :(

everything looks ok, but it doest let me select Takeoff!

GPS is 3D, Radio is ok, Link is ok...  >.>
Everything seems to be working perfectly. I can switch between modes normally, even start the engines in Auto1 and manual, all actuators are responding properly when moving the airplane around.

Any ideas?

Thanks Very Much!

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel