Re: [Paparazzi-devel] can't get any response from lisa/m even telemetry

ok...default baud rate is 57000 for use 9600 baud you need to add this in you configuration file...

Its posible To you make a better picture of your modem connecttion and especified the pin connections in the picture like my picture i send to you...and take snapshot of your errors

El 14/02/2014 08:23, "evan igor" <address@hidden> escribió:

Hi ,
thanks LUIS for your response
i tried to add the rules but the same thing waiting for telemetry.

if you allow i'll review with you the steps i did:

1- connecting all h/w as the picture i sent you.
2- disable mavlink protocol for 3dr and convrting its baudrate with 9600 to try and fail with 5700.
3- build the firmware default of lisam_2 quadrotor after uploading disconnect usb cable.

4- press the execute with usb_9600.
5- the three agents ran with no errors server, GCS, Datalink.
6- before that i tested the 3dr by connecting the rx with tx for testing and open terminal and try to send random numbers and it works fine,

after these all the same thing waiting for telemetry.
On Fri, Feb 14, 2014 at 12:25 PM, Luis Carlos <address@hidden> wrote:
Hi...You need to apply this command for add udev rules

cd <your paparazzi directory>
sudo cp conf/system/udev/rules/50-paparazzi.rules /etc/udev/rules.d/

More information here

http://wiki.paparazziuav.org/wiki/Udev

Luis Carlos
El 14/02/2014 03:59, "evan igor" <address@hidden> escribió:
i tried to change the baudrate from 5700 to 9600 in CGS although my modem set to 5700 but it works instantenously as there is no error appeared when press execute but still
waiting for telemetry in CGS
On Fri, Feb 14, 2014 at 8:49 AM, evan igor <address@hidden> wrote:
HI,
i made setup for udev rules

aren't these commands which you mean
sudo adduser <your login> plugdev
sudo adduser <your login> dialout
On Fri, Feb 14, 2014 at 5:28 AM, Luis Carlos <address@hidden> wrote:

when installing gcs you add udev rules? This is necessary for handle usb connection...
Regards

Luis Carlos

El 13/02/2014 21:20, "evan igor" <address@hidden> escribió:

i tried the Bixler example but the same problem no telemtry although i tested the 3fr with mission planner and it works fine and redisable the mavlink protocol and try with paparazzi but no data.

any help

On Fri, Feb 14, 2014 at 1:37 AM, evan igor <address@hidden> wrote:

should i try your firmware?

On Fri, Feb 14, 2014 at 1:08 AM, Luis Carlos <address@hidden> wrote:

http://lists.paparazziuav.org/First-Flight-lisa-m-fixedwing-throttle-auto-2-problem-td13923.html

Here you find my file...

Luis Carlos

El 13/02/2014 19:53, "evan igor" <address@hidden> escribió:

it's part of quad_ lisam_2 you mean i should try the bixler firmware example.

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

From:	Luis Carlos
Subject:	Re: [Paparazzi-devel] can't get any response from lisa/m even telemetry
Date:	Fri, 14 Feb 2014 08:55:35 -0300