Re: [Paparazzi-devel] errors during cc3d revo compile #2

On Thu, May 19, 2016 at 5:48 PM, Felix Ruess <address@hidden> wrote:

If you want to USE_BARO_BOARD, you also have to add the baro to baro_board.makefile and baro_board.h in the board folder.
See e.g. https://github.com/flixr/paparazzi/commit/eb5ecd494b393520fc47fbc8ce932f93b29a3f4c#diff-1e5e2b52154a92d33d68378eaf23cc1e

On Thu, May 19, 2016 at 4:35 PM, hendrixgr . <address@hidden> wrote:
Hi i use a modified revo version that i wrote after examining the mini revo board (the one without the onboard modem)
and yes it has the USE_BARO_BOARD set to TRUE.
If i set it to FALSE everything compiles fine.
The paparazzi version is the 5.8.1 stable

#ifndef CONFIG_OPENPILOT_REVO_MINI_1_0_H
#define CONFIG_OPENPILOT_REVO_MINI_1_0_H

#define BOARD_REVO

/* OpenPilot Revo has a 8MHz external clock and 168MHz internal. */
#define EXT_CLK 8000000
#define AHB_CLK 168000000

#if defined(USE_I2C2) && defined(USE_UART3)
#error CANNOT USE I2C2 AND UART3 BOTH AT THE SAME TIME
#endif

/*
* Onboard LEDs
*/

/* STAT blue, on PB5 */
#ifndef USE_LED_1
#define USE_LED_1 1
#endif
#define LED_1_GPIO GPIOB
#define LED_1_GPIO_PIN GPIO5
#define LED_1_GPIO_ON gpio_clear
#define LED_1_GPIO_OFF gpio_set
#define LED_1_AFIO_REMAP ((void)0)

/* WARN red, on PB4 */
#ifndef USE_LED_2
#define USE_LED_2 1
#endif
#define LED_2_GPIO GPIOB
#define LED_2_GPIO_PIN GPIO4
#define LED_2_GPIO_ON gpio_clear
#define LED_2_GPIO_OFF gpio_set
#define LED_2_AFIO_REMAP ((void)0)

/* Default actuators driver */
#define DEFAULT_ACTUATORS "subsystems/actuators/actuators_pwm.h"
#define ActuatorDefaultSet(_x,_y) ActuatorPwmSet(_x,_y)
#define ActuatorsDefaultInit() ActuatorsPwmInit()
#define ActuatorsDefaultCommit() ActuatorsPwmCommit()

/* UART */
//CAN BE USED AS GPS SERIAL PORT, CONNECTED TO MAIN PORT PLUG
#define UART1_GPIO_AF GPIO_AF7
#define UART1_GPIO_PORT_TX GPIOA
#define UART1_GPIO_TX GPIO9
#define UART1_GPIO_PORT_RX GPIOA
#define UART1_GPIO_RX GPIO10

//CANNOT BE USED IF SERVO3 AND SERVO4 ARE USED
#if (!defined(USE_PWM3) || USE_PWM3 == 0) && (!defined(USE_PWM4) || USE_PWM4 == 0)
#if (!defined(USE_ADC_3) || USE_ADC_3 == 0) && (!defined(USE_ADC_4) || USE_ADC_4 == 0)
#define UART2_GPIO_AF GPIO_AF7
#define UART2_GPIO_PORT_TX GPIOA
#define UART2_GPIO_TX GPIO2
#define UART2_GPIO_PORT_RX GPIOA
#define UART2_GPIO_RX GPIO3
#endif
#endif

//CANNOT BE USED IF IC2 IS NEEDED, CONNECTED TO FLEXI PORT PLUG
#if !defined(USE_I2C2)
#define UART3_GPIO_AF GPIO_AF7
#define UART3_GPIO_PORT_TX GPIOB
#define UART3_GPIO_TX GPIO10
#define UART3_GPIO_PORT_RX GPIOB
#define UART3_GPIO_RX GPIO11
#endif

//CANNOT BE USED IF SPI3 IS NEEDED, CONNECTED TO OPLINK PORT PLUG.
#define UART5_GPIO_AF GPIO_AF8
#define UART5_GPIO_PORT_RX GPIOD
#define UART5_GPIO_RX GPIO2
#define UART5_GPIO_PORT_TX GPIOC
#define UART5_GPIO_TX GPIO12

//CONNECTED TO RX INPUT PORT PLUG.
#define UART6_GPIO_AF GPIO_AF8
#define UART6_GPIO_PORT_RX GPIOC
#define UART6_GPIO_RX GPIO7
#define UART6_GPIO_PORT_TX GPIOC
#define UART6_GPIO_TX GPIO6

/* SPI */
/* MPU6000 */
#define SPI1_GPIO_AF GPIO_AF5
#define SPI1_GPIO_PORT_MISO GPIOA
#define SPI1_GPIO_MISO GPIO6
#define SPI1_GPIO_PORT_MOSI GPIOA
#define SPI1_GPIO_MOSI GPIO7
#define SPI1_GPIO_PORT_SCK GPIOA
#define SPI1_GPIO_SCK GPIO5
#define SPI1_GPIO_PORT_NSS GPIOA
#define SPI1_GPIO_NSS GPIO4

/* flash and RFM22B-S2 modem */
#define SPI3_GPIO_AF GPIO_AF5
#define SPI3_GPIO_PORT_MISO GPIOC
#define SPI3_GPIO_MISO GPIO11
#define SPI3_GPIO_PORT_MOSI GPIOC
#define SPI3_GPIO_MOSI GPIO12
#define SPI3_GPIO_PORT_SCK GPIOC
#define SPI3_GPIO_SCK GPIO10
/* modem CS */
#define SPI3_GPIO_PORT_NSS GPIOA
#define SPI3_GPIO_NSS GPIO15

/* MODEM select */
#define SPI_SELECT_SLAVE0_PORT GPIOA
#define SPI_SELECT_SLAVE0_PIN GPIO15

/* external flash chip select */
#define SPI_SELECT_SLAVE1_PORT GPIOB
#define SPI_SELECT_SLAVE1_PIN GPIO3

/* MPU6000 select */
#define SPI_SELECT_SLAVE2_PORT GPIOA
#define SPI_SELECT_SLAVE2_PIN GPIO4

/* I2C mapping */
/* HMC5883L mag on I2C1 with DRDY on PB7 */
/* MS5611 baro on I2C1 */
#define I2C1_GPIO_PORT GPIOB
#define I2C1_GPIO_SCL GPIO8
#define I2C1_GPIO_SDA GPIO9

//CANNOT BE USED IF UART3 IS NEEDED, CONNECTED TO FLEXI PORT PLUG
#if !defined(USE_UART3)
#define I2C2_GPIO_PORT GPIOB
#define I2C2_GPIO_SCL GPIO10
#define I2C2_GPIO_SDA GPIO11
#endif

/*
* ADC
*/

/* Onboard ADCs */
/*
   ADC1 PC2/ADC12
   ADC2 PC1/ADC11
   ADC3 PA3/ADC3
   ADC4 PA2/ADC2
*/

/* provide defines that can be used to access the ADC_x in the code or airframe file
* these directly map to the index number of the 4 adc channels defined above
* 4th (index 3) is used for bat monitoring by default
*/

#define USE_AD_TIM2 1

#ifndef USE_ADC_1
#define USE_ADC_1 1
#endif

#ifndef USE_ADC_2
#define USE_ADC_2 1
#endif

/* Voltage on Pwr/Sen/Sonar CONN3 */
#if USE_ADC_1
#define AD1_1_CHANNEL 12
#define ADC_1 AD1_1
#define ADC_1_GPIO_PORT GPIOC
#define ADC_1_GPIO_PIN GPIO2
#endif

/* Current on Pwr/Sen/Sonar CONN3 */
#if USE_ADC_2
#define AD1_2_CHANNEL 11
#define ADC_2 AD1_2
#define ADC_2_GPIO_PORT GPIOC
#define ADC_2_GPIO_PIN GPIO1
#endif

/* FREE ON SERVO 3 */
#if USE_ADC_3
#define AD1_3_CHANNEL 3
#define ADC_3 AD1_3
#define ADC_3_GPIO_PORT GPIOA
#define ADC_3_GPIO_PIN GPIO3
#endif

/* FREE ON SERVO 4 */
#if USE_ADC_4
#define AD1_4_CHANNEL 2
#define ADC_4 AD1_4
#define ADC_4_GPIO_PORT GPIOA
#define ADC_4_GPIO_PIN GPIO2
#endif

/* allow to define ADC_CHANNEL_VSUPPLY in the airframe file*/
#ifndef ADC_CHANNEL_VSUPPLY
#define ADC_CHANNEL_VSUPPLY ADC_1
#endif

/* no voltage divider on board, adjust VoltageOfAdc in airframe file */
#define DefaultVoltageOfAdc(adc) (0.0045*adc)

/*
* PWM
*
*/
#define PWM_USE_TIM3 1
#define PWM_USE_TIM5 1
#if (defined(USE_ADC_3) && USE_ADC_3) || (defined(USE_ADC_4) && USE_ADC_4)
#define PWM_USE_TIM9 1
#endif

#define USE_PWM1 1
#define USE_PWM2 1
#define USE_PWM3 1
#define USE_PWM4 1
#define USE_PWM5 1
#define USE_PWM6 1
#define USE_PWM7 1
#define USE_PWM8 1

// PWM_SERVO_x is the index of the servo in the actuators_pwm_values array
#if USE_PWM1
#define PWM_SERVO_1 0
#define PWM_SERVO_1_TIMER TIM3
#define PWM_SERVO_1_GPIO GPIOB
#define PWM_SERVO_1_PIN GPIO0
#define PWM_SERVO_1_AF GPIO_AF2
#define PWM_SERVO_1_OC TIM_OC3
#define PWM_SERVO_1_OC_BIT (1<<2)
#else
#define PWM_SERVO_1_OC_BIT 0
#endif

#if USE_PWM2
#define PWM_SERVO_2 1
#define PWM_SERVO_2_TIMER TIM3
#define PWM_SERVO_2_GPIO GPIOB
#define PWM_SERVO_2_PIN GPIO1
#define PWM_SERVO_2_AF GPIO_AF2
#define PWM_SERVO_2_OC TIM_OC4
#define PWM_SERVO_2_OC_BIT (1<<3)
#else
#define PWM_SERVO_2_OC_BIT 0
#endif

#if USE_PWM3 && (!defined(USE_ADC_3) || USE_ADC_3 != 1)
#define PWM_SERVO_3 2
#define PWM_SERVO_3_TIMER TIM9
#define PWM_SERVO_3_GPIO GPIOA
#define PWM_SERVO_3_PIN GPIO3
#define PWM_SERVO_3_AF GPIO_AF3
#define PWM_SERVO_3_OC TIM_OC2
#define PWM_SERVO_3_OC_BIT (1<<1)
#else
#define PWM_SERVO_3_OC_BIT 0
#undef USE_PWM3
#warning SERVO 3 NOT AVAILABLE
#endif

#if USE_PWM4 && (!defined(USE_ADC_4) || USE_ADC_4 != 1)
#define PWM_SERVO_4 3
#define PWM_SERVO_4_TIMER TIM9
#define PWM_SERVO_4_GPIO GPIOA
#define PWM_SERVO_4_PIN GPIO2
#define PWM_SERVO_4_AF GPIO_AF3
#define PWM_SERVO_4_OC TIM_OC1
#define PWM_SERVO_4_OC_BIT (1<<0)
#else
#define PWM_SERVO_4_OC_BIT 0
#undef USE_PWM4
#warning SERVO 4 NOT AVAILABLE
#endif

#if USE_PWM5
#define PWM_SERVO_5 4
#define PWM_SERVO_5_TIMER TIM5
#define PWM_SERVO_5_GPIO GPIOA
#define PWM_SERVO_5_PIN GPIO1
#define PWM_SERVO_5_AF GPIO_AF2
#define PWM_SERVO_5_OC TIM_OC2
#define PWM_SERVO_5_OC_BIT (1<<1)
#else
#define PWM_SERVO_5_OC_BIT 0
#endif

#if USE_PWM6
#define PWM_SERVO_6 5
#define PWM_SERVO_6_TIMER TIM5
#define PWM_SERVO_6_GPIO GPIOA
#define PWM_SERVO_6_PIN GPIO0
#define PWM_SERVO_6_AF GPIO_AF2
#define PWM_SERVO_6_OC TIM_OC1
#define PWM_SERVO_6_OC_BIT (1<<0)
#else
#define PWM_SERVO_6_OC_BIT 0
#endif

#if USE_PWM7
#define PWM_SERVO_7 6
#define PWM_SERVO_7_TIMER TIM12
#define PWM_SERVO_7_GPIO GPIOB
#define PWM_SERVO_7_PIN GPIO14
#define PWM_SERVO_7_AF GPIO_AF9
#define PWM_SERVO_7_OC TIM_OC1
#define PWM_SERVO_7_OC_BIT (1<<0)
#else
#define PWM_SERVO_7_OC_BIT 0
#endif

#if USE_PWM8
#define PWM_SERVO_8 7
#define PWM_SERVO_8_TIMER TIM12
#define PWM_SERVO_8_GPIO GPIOB
#define PWM_SERVO_8_PIN GPIO15
#define PWM_SERVO_8_AF GPIO_AF9
#define PWM_SERVO_8_OC TIM_OC2
#define PWM_SERVO_8_OC_BIT (1<<1)
#else
#define PWM_SERVO_8_OC_BIT 0
#endif

/* servos 1-2 on TIM3 */
#define PWM_TIM3_CHAN_MASK (PWM_SERVO_1_OC_BIT | PWM_SERVO_2_OC_BIT)
/* servos 3-4 on TIM9 */
#define PWM_TIM9_CHAN_MASK (PWM_SERVO_3_OC_BIT | PWM_SERVO_4_OC_BIT)
/* servos 5-6 on TIM5 */
#define PWM_TIM5_CHAN_MASK (PWM_SERVO_5_OC_BIT | PWM_SERVO_6_OC_BIT)
/* servos 7-8 on TIM12 */
#define PWM_TIM12_CHAN_MASK (PWM_SERVO_7_OC_BIT | PWM_SERVO_8_OC_BIT)

/* by default activate onboard baro */
#ifndef USE_BARO_BOARD
//#define USE_BARO_BOARD 1
#endif

/* PPM
*
* Default is PPM config 2, input on GPIOA1 (Servo pin 6)
*/

#ifndef PPM_CONFIG
#define PPM_CONFIG 1
#endif

#if PPM_CONFIG == 1
//#if defined(RADIO_CONTROL_PPM_PIN) && RADIO_CONTROL_PPM_PIN == SERVO_6_IN
/* input on PC9 (SERVO 6 IN) */
#define USE_PPM_TIM8 1
#define PPM_CHANNEL         TIM_IC4
#define PPM_TIMER_INPUT     TIM_IC_IN_TI4
#define PPM_IRQ             NVIC_TIM8_CC_IRQ
#define PPM_IRQ2            NVIC_TIM8_UP_TIM13_IRQ
// Capture/Compare InteruptEnable and InterruptFlag
#define PPM_CC_IE           TIM_DIER_CC4IE
#define PPM_CC_IF           TIM_SR_CC4IF
#define PPM_GPIO_PORT       GPIOC
#define PPM_GPIO_PIN        GPIO9
#define PPM_GPIO_AF         GPIO_AF3

#elif PPM_CONFIG == 2

/* input on PC8 (SERVO 5 IN) */
#define USE_PPM_TIM8 1
#define PPM_CHANNEL         TIM_IC3
#define PPM_TIMER_INPUT     TIM_IC_IN_TI3
#define PPM_IRQ             NVIC_TIM8_CC_IRQ
#define PPM_IRQ2            NVIC_TIM8_UP_TIM13_IRQ
// Capture/Compare InteruptEnable and InterruptFlag
#define PPM_CC_IE           TIM_DIER_CC3IE
#define PPM_CC_IF           TIM_SR_CC3IF
#define PPM_GPIO_PORT       GPIOC
#define PPM_GPIO_PIN        GPIO8
#define PPM_GPIO_AF         GPIO_AF3

#else
#error "Unknown PPM config"

#endif // PPM_CONFIG

/*
* Spektrum
*/
/* The line that is pulled low at power up to initiate the bind process */
#define SPEKTRUM_BIND_PIN GPIO0
#define SPEKTRUM_BIND_PIN_PORT GPIOB

#define SPEKTRUM_UART1_RCC RCC_USART1
#define SPEKTRUM_UART1_BANK GPIOA
#define SPEKTRUM_UART1_PIN GPIO10
#define SPEKTRUM_UART1_AF GPIO_AF7
#define SPEKTRUM_UART1_IRQ NVIC_USART1_IRQ
#define SPEKTRUM_UART1_ISR usart1_isr
#define SPEKTRUM_UART1_DEV USART1

#define SPEKTRUM_UART2_RCC RCC_USART2
#define SPEKTRUM_UART2_BANK GPIOA
#define SPEKTRUM_UART2_PIN GPIO3
#define SPEKTRUM_UART2_AF GPIO_AF7
#define SPEKTRUM_UART2_IRQ NVIC_USART2_IRQ
#define SPEKTRUM_UART2_ISR usart2_isr
#define SPEKTRUM_UART2_DEV USART2

#define SPEKTRUM_UART5_RCC RCC_UART5
#define SPEKTRUM_UART5_BANK GPIOD
#define SPEKTRUM_UART5_PIN GPIO2
#define SPEKTRUM_UART5_AF GPIO_AF8
#define SPEKTRUM_UART5_IRQ NVIC_UART5_IRQ
#define SPEKTRUM_UART5_ISR uart5_isr
#define SPEKTRUM_UART5_DEV UART5

#endif /* CONFIG_OPENPILOT_REVO_MINI_1_0_H */

On Thu, May 19, 2016 at 12:22 PM, Felix Ruess <address@hidden> wrote:
Hi Chris,

what paparazzi_version are you using and more importantly which board files are you using? The (untested) revo board files from my op_revo branch?
It seems that whatever you are using has USE_BARO_BOARD set to TRUE, but there is no onboard baro defined.
Just post you airframe file as well...

Cheers, Felix

On Wed, May 18, 2016 at 11:37 PM, hendrixgr . <address@hidden> wrote:
Ok i solved the ic20 error by changing the ms5611 module configuration from

   <load name="baro_ms5611_i2c.xml">
        <define name="MS5611_I2C_DEV" value="i2c1" />
        <define name="MS5611_SLAVE_ADDR=0xEE"/>
        <define name="MS5611_SEND_BARO_ALTITUDE"/>
    </load>
to

   <load name="baro_ms5611_i2c.xml">
        <configure name="MS5611_I2C_DEV" value="i2c1" />
        <define name="MS5611_SLAVE_ADDR=0xEE"/>
        <define name="MS5611_SEND_BARO_ALTITUDE"/>
    </load>

but i do get the below error and i am not that experienced with the baro files.

/home/hendrix/paparazzi/var/aircrafts/xeno/ap/firmwares/fixedwing/main_ap.o: In function `init_ap':
/home/hendrix/paparazzi/sw/airborne/firmwares/fixedwing/main_ap.c:214: undefined reference to `baro_init'
/home/hendrix/paparazzi/var/aircrafts/xeno/ap/firmwares/fixedwing/main_ap.o: In function `handle_periodic_tasks_ap':
/home/hendrix/paparazzi/sw/airborne/firmwares/fixedwing/main_ap.c:287: undefined reference to `baro_periodic'
/home/hendrix/paparazzi/var/aircrafts/xeno/ap/firmwares/fixedwing/main_ap.o: In function `event_task_ap':
/home/hendrix/paparazzi/sw/airborne/firmwares/fixedwing/main_ap.c:714: undefined reference to `baro_event'
collect2: error: ld returned 1 exit status
make[1]: *** [/home/hendrix/paparazzi/var/aircrafts/xeno/ap/ap.elf] Error 1
make[1]: Leaving directory `/home/hendrix/paparazzi/sw/airborne'
make: *** [ap.compile] Error 2
make: Leaving directory `/home/hendrix/paparazzi'

Chris

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

From:	hendrixgr .
Subject:	Re: [Paparazzi-devel] errors during cc3d revo compile #2
Date:	Thu, 19 May 2016 18:43:39 +0300