Re: [Qemu-arm] [Qemu-devel] [PATCH v5 13/28] tests/pflash-cfi02: Refactor to support testing multiple configurations

[Alistair Francis]

On Thu, Jun 27, 2019 at 1:50 PM Philippe Mathieu-Daudé
<address@hidden> wrote:
>
> Introduce the FlashConfig structure, to be able to run the same set
> of tests on different flash models/configurations.
>
> Signed-off-by: Stephen Checkoway <address@hidden>
> Message-Id: <address@hidden>
> [PMD: Extracted from bigger patch]
> Signed-off-by: Philippe Mathieu-Daudé <address@hidden>

Acked-by: Alistair Francis <address@hidden>

Alistair

> ---
>  tests/pflash-cfi02-test.c | 386 +++++++++++++++++++++++++++-----------
>  1 file changed, 277 insertions(+), 109 deletions(-)
>
> diff --git a/tests/pflash-cfi02-test.c b/tests/pflash-cfi02-test.c
> index e090b2e3a0..b00f5ca2e7 100644
> --- a/tests/pflash-cfi02-test.c
> +++ b/tests/pflash-cfi02-test.c
> @@ -17,12 +17,18 @@
>   */
>
>  #define MP_FLASH_SIZE_MAX (32 * 1024 * 1024)
> +#define FLASH_SIZE (8 * 1024 * 1024)
>  #define BASE_ADDR (0x100000000ULL - MP_FLASH_SIZE_MAX)
>
> -#define FLASH_WIDTH 2
> -#define CFI_ADDR (FLASH_WIDTH * 0x55)
> -#define UNLOCK0_ADDR (FLASH_WIDTH * 0x555)
> -#define UNLOCK1_ADDR (FLASH_WIDTH * 0x2AA)
> +/* Use a newtype to keep flash addresses separate from byte addresses. */
> +typedef struct {
> +    uint64_t addr;
> +} faddr;
> +#define FLASH_ADDR(x) ((faddr) { .addr = (x) })
> +
> +#define CFI_ADDR FLASH_ADDR(0x55)
> +#define UNLOCK0_ADDR FLASH_ADDR(0x555)
> +#define UNLOCK1_ADDR FLASH_ADDR(0x2AA)
>
>  #define CFI_CMD 0x98
>  #define UNLOCK0_CMD 0xAA
> @@ -35,170 +41,313 @@
>  #define UNLOCK_BYPASS_CMD 0x20
>  #define UNLOCK_BYPASS_RESET_CMD 0x00
>
> +typedef struct {
> +    int bank_width;
> +
> +    QTestState *qtest;
> +} FlashConfig;
> +
>  static char image_path[] = "/tmp/qtest.XXXXXX";
>
> -static inline void flash_write(uint64_t byte_addr, uint16_t data)
> +/*
> + * The pflash implementation allows some parameters to be unspecified. We 
> want
> + * to test those configurations but we also need to know the real values in
> + * our testing code. So after we launch qemu, we'll need a new FlashConfig
> + * with the correct values filled in.
> + */
> +static FlashConfig expand_config_defaults(const FlashConfig *c)
>  {
> -    qtest_writew(global_qtest, BASE_ADDR + byte_addr, data);
> +    FlashConfig ret = *c;
> +
> +    if (ret.bank_width == 0) {
> +        ret.bank_width = 2;
> +    }
> +
> +    /* XXX: Limitations of test harness. */
> +    assert(ret.bank_width == 2);
> +    return ret;
>  }
>
> -static inline uint16_t flash_read(uint64_t byte_addr)
> +/*
> + * Return a bit mask suitable for extracting the least significant
> + * status/query response from an interleaved response.
> + */
> +static inline uint64_t device_mask(const FlashConfig *c)
>  {
> -    return qtest_readw(global_qtest, BASE_ADDR + byte_addr);
> +    return (uint64_t)-1;
>  }
>
> -static void unlock(void)
> +/*
> + * Return a bit mask exactly as long as the bank_width.
> + */
> +static inline uint64_t bank_mask(const FlashConfig *c)
>  {
> -    flash_write(UNLOCK0_ADDR, UNLOCK0_CMD);
> -    flash_write(UNLOCK1_ADDR, UNLOCK1_CMD);
> +    if (c->bank_width == 8) {
> +        return (uint64_t)-1;
> +    }
> +    return (1ULL << (c->bank_width * 8)) - 1ULL;
>  }
>
> -static void reset(void)
> +static inline void flash_write(const FlashConfig *c, uint64_t byte_addr,
> +                               uint64_t data)
>  {
> -    flash_write(0, RESET_CMD);
> -}
> -
> -static void sector_erase(uint64_t byte_addr)
> -{
> -    unlock();
> -    flash_write(UNLOCK0_ADDR, 0x80);
> -    unlock();
> -    flash_write(byte_addr, SECTOR_ERASE_CMD);
> -}
> -
> -static void wait_for_completion(uint64_t byte_addr)
> -{
> -    /* If DQ6 is toggling, step the clock and ensure the toggle stops. */
> -    if ((flash_read(byte_addr) & 0x40) ^ (flash_read(byte_addr) & 0x40)) {
> -        /* Wait for erase or program to finish. */
> -        clock_step_next();
> -        /* Ensure that DQ6 has stopped toggling. */
> -        g_assert_cmphex(flash_read(byte_addr), ==, flash_read(byte_addr));
> +    /* Sanity check our tests. */
> +    assert((data & ~bank_mask(c)) == 0);
> +    uint64_t addr = BASE_ADDR + byte_addr;
> +    switch (c->bank_width) {
> +    case 1:
> +        qtest_writeb(c->qtest, addr, data);
> +        break;
> +    case 2:
> +        qtest_writew(c->qtest, addr, data);
> +        break;
> +    case 4:
> +        qtest_writel(c->qtest, addr, data);
> +        break;
> +    case 8:
> +        qtest_writeq(c->qtest, addr, data);
> +        break;
> +    default:
> +        abort();
>      }
>  }
>
> -static void bypass_program(uint64_t byte_addr, uint16_t data)
> +static inline uint64_t flash_read(const FlashConfig *c, uint64_t byte_addr)
>  {
> -    flash_write(UNLOCK0_ADDR, PROGRAM_CMD);
> -    flash_write(byte_addr, data);
> +    uint64_t addr = BASE_ADDR + byte_addr;
> +    switch (c->bank_width) {
> +    case 1:
> +        return qtest_readb(c->qtest, addr);
> +    case 2:
> +        return qtest_readw(c->qtest, addr);
> +    case 4:
> +        return qtest_readl(c->qtest, addr);
> +    case 8:
> +        return qtest_readq(c->qtest, addr);
> +    default:
> +        abort();
> +    }
> +}
> +
> +/*
> + * Convert a flash address expressed in the maximum width of the device as a
> + * byte address.
> + */
> +static inline uint64_t as_byte_addr(const FlashConfig *c, faddr flash_addr)
> +{
> +    /*
> +     * Command addresses are always given as addresses in the maximum
> +     * supported bus size for the flash chip. So an x8/x16 chip in x8 mode
> +     * uses addresses 0xAAA and 0x555 to unlock because the least significant
> +     * bit is ignored. (0x555 rather than 0x554 is traditional.)
> +     *
> +     * In general we need to multiply by the maximum device width.
> +     */
> +    return flash_addr.addr * c->bank_width;
> +}
> +
> +/*
> + * Return the command value or expected status replicated across all devices.
> + */
> +static inline uint64_t replicate(const FlashConfig *c, uint64_t data)
> +{
> +    /* Sanity check our tests. */
> +    assert((data & ~device_mask(c)) == 0);
> +    return data;
> +}
> +
> +static inline void flash_cmd(const FlashConfig *c, faddr cmd_addr,
> +                             uint8_t cmd)
> +{
> +    flash_write(c, as_byte_addr(c, cmd_addr), replicate(c, cmd));
> +}
> +
> +static inline uint64_t flash_query(const FlashConfig *c, faddr query_addr)
> +{
> +    return flash_read(c, as_byte_addr(c, query_addr));
> +}
> +
> +static inline uint64_t flash_query_1(const FlashConfig *c, faddr query_addr)
> +{
> +    return flash_query(c, query_addr) & device_mask(c);
> +}
> +
> +static void unlock(const FlashConfig *c)
> +{
> +    flash_cmd(c, UNLOCK0_ADDR, UNLOCK0_CMD);
> +    flash_cmd(c, UNLOCK1_ADDR, UNLOCK1_CMD);
> +}
> +
> +static void reset(const FlashConfig *c)
> +{
> +    flash_cmd(c, FLASH_ADDR(0), RESET_CMD);
> +}
> +
> +static void sector_erase(const FlashConfig *c, uint64_t byte_addr)
> +{
> +    unlock(c);
> +    flash_cmd(c, UNLOCK0_ADDR, 0x80);
> +    unlock(c);
> +    flash_write(c, byte_addr, replicate(c, SECTOR_ERASE_CMD));
> +}
> +
> +static void wait_for_completion(const FlashConfig *c, uint64_t byte_addr)
> +{
> +    /* If DQ6 is toggling, step the clock and ensure the toggle stops. */
> +    const uint64_t dq6 = replicate(c, 0x40);
> +    if ((flash_read(c, byte_addr) & dq6) ^ (flash_read(c, byte_addr) & dq6)) 
> {
> +        /* Wait for erase or program to finish. */
> +        qtest_clock_step_next(c->qtest);
> +        /* Ensure that DQ6 has stopped toggling. */
> +        g_assert_cmphex(flash_read(c, byte_addr), ==, flash_read(c, 
> byte_addr));
> +    }
> +}
> +
> +static void bypass_program(const FlashConfig *c, uint64_t byte_addr,
> +                           uint16_t data)
> +{
> +    flash_cmd(c, UNLOCK0_ADDR, PROGRAM_CMD);
> +    flash_write(c, byte_addr, data);
>      /*
>       * Data isn't valid until DQ6 stops toggling. We don't model this as
>       * writes are immediate, but if this changes in the future, we can wait
>       * until the program is complete.
>       */
> -    wait_for_completion(byte_addr);
> +    wait_for_completion(c, byte_addr);
>  }
>
> -static void program(uint64_t byte_addr, uint16_t data)
> +static void program(const FlashConfig *c, uint64_t byte_addr, uint16_t data)
>  {
> -    unlock();
> -    bypass_program(byte_addr, data);
> +    unlock(c);
> +    bypass_program(c, byte_addr, data);
>  }
>
> -static void chip_erase(void)
> +static void chip_erase(const FlashConfig *c)
>  {
> -    unlock();
> -    flash_write(UNLOCK0_ADDR, 0x80);
> -    unlock();
> -    flash_write(UNLOCK0_ADDR, SECTOR_ERASE_CMD);
> +    unlock(c);
> +    flash_cmd(c, UNLOCK0_ADDR, 0x80);
> +    unlock(c);
> +    flash_cmd(c, UNLOCK0_ADDR, CHIP_ERASE_CMD);
>  }
>
> -static void test_flash(void)
> +static void test_flash(const void *opaque)
>  {
> -    global_qtest = qtest_initf("-M musicpal,accel=qtest "
> -                               "-drive 
> if=pflash,file=%s,format=raw,copy-on-read",
> -                               image_path);
> +    const FlashConfig *config = opaque;
> +    QTestState *qtest;
> +    qtest = qtest_initf("-M musicpal,accel=qtest"
> +                        " -drive if=pflash,file=%s,format=raw,copy-on-read",
> +                        image_path);
> +    FlashConfig explicit_config = expand_config_defaults(config);
> +    explicit_config.qtest = qtest;
> +    const FlashConfig *c = &explicit_config;
> +
>      /* Check the IDs. */
> -    unlock();
> -    flash_write(UNLOCK0_ADDR, AUTOSELECT_CMD);
> -    g_assert_cmphex(flash_read(FLASH_WIDTH * 0x0000), ==, 0x00BF);
> -    g_assert_cmphex(flash_read(FLASH_WIDTH * 0x0001), ==, 0x236D);
> -    reset();
> +    unlock(c);
> +    flash_cmd(c, UNLOCK0_ADDR, AUTOSELECT_CMD);
> +    g_assert_cmphex(flash_query(c, FLASH_ADDR(0)), ==, replicate(c, 0xBF));
> +    if (c->bank_width >= 2) {
> +        /*
> +         * XXX: The ID returned by the musicpal flash chip is 16 bits which
> +         * wouldn't happen with an 8-bit device. It would probably be best to
> +         * prohibit addresses larger than the device width in pflash_cfi02.c,
> +         * but then we couldn't test smaller device widths at all.
> +         */
> +        g_assert_cmphex(flash_query(c, FLASH_ADDR(1)), ==,
> +                        replicate(c, 0x236D));
> +    }
> +    reset(c);
>
>      /* Check the erase blocks. */
> -    flash_write(CFI_ADDR, CFI_CMD);
> -    g_assert_cmphex(flash_read(FLASH_WIDTH * 0x10), ==, 'Q');
> -    g_assert_cmphex(flash_read(FLASH_WIDTH * 0x11), ==, 'R');
> -    g_assert_cmphex(flash_read(FLASH_WIDTH * 0x12), ==, 'Y');
> -    /* Num erase regions. */
> -    g_assert_cmphex(flash_read(FLASH_WIDTH * 0x2C), >=, 1);
> -    uint32_t nb_sectors = flash_read(FLASH_WIDTH * 0x2D) +
> -                          (flash_read(FLASH_WIDTH * 0x2E) << 8) + 1;
> -    uint32_t sector_len = (flash_read(FLASH_WIDTH * 0x2F) << 8) +
> -                          (flash_read(FLASH_WIDTH * 0x30) << 16);
> -    reset();
> +    flash_cmd(c, CFI_ADDR, CFI_CMD);
> +    g_assert_cmphex(flash_query(c, FLASH_ADDR(0x10)), ==, replicate(c, 'Q'));
> +    g_assert_cmphex(flash_query(c, FLASH_ADDR(0x11)), ==, replicate(c, 'R'));
> +    g_assert_cmphex(flash_query(c, FLASH_ADDR(0x12)), ==, replicate(c, 'Y'));
>
> +    /* Num erase regions. */
> +    g_assert_cmphex(flash_query_1(c, FLASH_ADDR(0x2C)), >=, 1);
> +
> +    uint32_t nb_sectors = flash_query_1(c, FLASH_ADDR(0x2D)) +
> +                          (flash_query_1(c, FLASH_ADDR(0x2E)) << 8) + 1;
> +    uint32_t sector_len = (flash_query_1(c, FLASH_ADDR(0x2F)) << 8) +
> +                          (flash_query_1(c, FLASH_ADDR(0x30)) << 16);
> +    reset(c);
> +
> +    const uint64_t dq7 = replicate(c, 0x80);
> +    const uint64_t dq6 = replicate(c, 0x40);
>      /* Erase and program sector. */
>      for (uint32_t i = 0; i < nb_sectors; ++i) {
>          uint64_t byte_addr = i * sector_len;
> -        sector_erase(byte_addr);
> +        sector_erase(c, byte_addr);
>          /* Read toggle. */
> -        uint16_t status0 = flash_read(byte_addr);
> +        uint64_t status0 = flash_read(c, byte_addr);
>          /* DQ7 is 0 during an erase. */
> -        g_assert_cmphex(status0 & 0x80, ==, 0);
> -        uint16_t status1 = flash_read(byte_addr);
> +        g_assert_cmphex(status0 & dq7, ==, 0);
> +        uint64_t status1 = flash_read(c, byte_addr);
>          /* DQ6 toggles during an erase. */
> -        g_assert_cmphex(status0 & 0x40, !=, status1 & 0x40);
> +        g_assert_cmphex(status0 & dq6, ==, ~status1 & dq6);
>          /* Wait for erase to complete. */
> -        clock_step_next();
> +        qtest_clock_step_next(c->qtest);
>          /* Ensure DQ6 has stopped toggling. */
> -        g_assert_cmphex(flash_read(byte_addr), ==, flash_read(byte_addr));
> +        g_assert_cmphex(flash_read(c, byte_addr), ==, flash_read(c, 
> byte_addr));
>          /* Now the data should be valid. */
> -        g_assert_cmphex(flash_read(byte_addr), ==, 0xFFFF);
> +        g_assert_cmphex(flash_read(c, byte_addr), ==, bank_mask(c));
>
>          /* Program a bit pattern. */
> -        program(byte_addr, 0x5555);
> -        g_assert_cmphex(flash_read(byte_addr), ==, 0x5555);
> -        program(byte_addr, 0xAA55);
> -        g_assert_cmphex(flash_read(byte_addr), ==, 0x0055);
> +        program(c, byte_addr, 0x55);
> +        g_assert_cmphex(flash_read(c, byte_addr) & 0xFF, ==, 0x55);
> +        program(c, byte_addr, 0xA5);
> +        g_assert_cmphex(flash_read(c, byte_addr) & 0xFF, ==, 0x05);
>      }
>
>      /* Erase the chip. */
> -    chip_erase();
> +    chip_erase(c);
>      /* Read toggle. */
> -    uint16_t status0 = flash_read(0);
> +    uint64_t status0 = flash_read(c, 0);
>      /* DQ7 is 0 during an erase. */
> -    g_assert_cmphex(status0 & 0x80, ==, 0);
> -    uint16_t status1 = flash_read(0);
> +    g_assert_cmphex(status0 & dq7, ==, 0);
> +    uint64_t status1 = flash_read(c, 0);
>      /* DQ6 toggles during an erase. */
> -    g_assert_cmphex(status0 & 0x40, !=, status1 & 0x40);
> +    g_assert_cmphex(status0 & dq6, ==, ~status1 & dq6);
>      /* Wait for erase to complete. */
> -    clock_step_next();
> +    qtest_clock_step_next(c->qtest);
>      /* Ensure DQ6 has stopped toggling. */
> -    g_assert_cmphex(flash_read(0), ==, flash_read(0));
> +    g_assert_cmphex(flash_read(c, 0), ==, flash_read(c, 0));
>      /* Now the data should be valid. */
> -    g_assert_cmphex(flash_read(0), ==, 0xFFFF);
> +
> +    for (uint32_t i = 0; i < nb_sectors; ++i) {
> +        uint64_t byte_addr = i * sector_len;
> +        g_assert_cmphex(flash_read(c, byte_addr), ==, bank_mask(c));
> +    }
>
>      /* Unlock bypass */
> -    unlock();
> -    flash_write(UNLOCK0_ADDR, UNLOCK_BYPASS_CMD);
> -    bypass_program(0, 0x0123);
> -    bypass_program(2, 0x4567);
> -    bypass_program(4, 0x89AB);
> +    unlock(c);
> +    flash_cmd(c, UNLOCK0_ADDR, UNLOCK_BYPASS_CMD);
> +    bypass_program(c, 0 * c->bank_width, 0x01);
> +    bypass_program(c, 1 * c->bank_width, 0x23);
> +    bypass_program(c, 2 * c->bank_width, 0x45);
>      /*
>       * Test that bypass programming, unlike normal programming can use any
>       * address for the PROGRAM_CMD.
>       */
> -    flash_write(6, PROGRAM_CMD);
> -    flash_write(6, 0xCDEF);
> -    wait_for_completion(6);
> -    flash_write(0, UNLOCK_BYPASS_RESET_CMD);
> -    bypass_program(8, 0x55AA); /* Should fail. */
> -    g_assert_cmphex(flash_read(0), ==, 0x0123);
> -    g_assert_cmphex(flash_read(2), ==, 0x4567);
> -    g_assert_cmphex(flash_read(4), ==, 0x89AB);
> -    g_assert_cmphex(flash_read(6), ==, 0xCDEF);
> -    g_assert_cmphex(flash_read(8), ==, 0xFFFF);
> +    flash_cmd(c, FLASH_ADDR(3 * c->bank_width), PROGRAM_CMD);
> +    flash_write(c, 3 * c->bank_width, 0x67);
> +    wait_for_completion(c, 3 * c->bank_width);
> +    flash_cmd(c, FLASH_ADDR(0), UNLOCK_BYPASS_RESET_CMD);
> +    bypass_program(c, 4 * c->bank_width, 0x89); /* Should fail. */
> +    g_assert_cmphex(flash_read(c, 0 * c->bank_width), ==, 0x01);
> +    g_assert_cmphex(flash_read(c, 1 * c->bank_width), ==, 0x23);
> +    g_assert_cmphex(flash_read(c, 2 * c->bank_width), ==, 0x45);
> +    g_assert_cmphex(flash_read(c, 3 * c->bank_width), ==, 0x67);
> +    g_assert_cmphex(flash_read(c, 4 * c->bank_width), ==, bank_mask(c));
>
>      /* Test ignored high order bits of address. */
> -    flash_write(FLASH_WIDTH * 0x5555, UNLOCK0_CMD);
> -    flash_write(FLASH_WIDTH * 0x2AAA, UNLOCK1_CMD);
> -    flash_write(FLASH_WIDTH * 0x5555, AUTOSELECT_CMD);
> -    g_assert_cmpint(flash_read(FLASH_WIDTH * 0x0000), ==, 0x00BF);
> -    g_assert_cmpint(flash_read(FLASH_WIDTH * 0x0001), ==, 0x236D);
> -    reset();
> +    flash_cmd(c, FLASH_ADDR(0x5555), UNLOCK0_CMD);
> +    flash_cmd(c, FLASH_ADDR(0x2AAA), UNLOCK1_CMD);
> +    flash_cmd(c, FLASH_ADDR(0x5555), AUTOSELECT_CMD);
> +    g_assert_cmphex(flash_query(c, FLASH_ADDR(0)), ==, replicate(c, 0xBF));
> +    reset(c);
>
> -    qtest_quit(global_qtest);
> +    qtest_quit(qtest);
>  }
>
>  static void cleanup(void *opaque)
> @@ -206,6 +355,17 @@ static void cleanup(void *opaque)
>      unlink(image_path);
>  }
>
> +/*
> + * XXX: Tests are limited to bank_width = 2 for now because that's what
> + * hw/arm/musicpal.c has.
> + */
> +static const FlashConfig configuration[] = {
> +    /* One x16 device. */
> +    {
> +        .bank_width = 2,
> +    },
> +};
> +
>  int main(int argc, char **argv)
>  {
>      int fd = mkstemp(image_path);
> @@ -214,19 +374,27 @@ int main(int argc, char **argv)
>                     strerror(errno));
>          exit(EXIT_FAILURE);
>      }
> -    if (ftruncate(fd, 8 * 1024 * 1024) < 0) {
> +    if (ftruncate(fd, FLASH_SIZE) < 0) {
>          int error_code = errno;
>          close(fd);
>          unlink(image_path);
> -        g_printerr("Failed to truncate file %s to 8 MB: %s\n", image_path,
> -                   strerror(error_code));
> +        g_printerr("Failed to truncate file %s to %u MB: %s\n", image_path,
> +                   FLASH_SIZE, strerror(error_code));
>          exit(EXIT_FAILURE);
>      }
>      close(fd);
>
>      qtest_add_abrt_handler(cleanup, NULL);
>      g_test_init(&argc, &argv, NULL);
> -    qtest_add_func("pflash-cfi02", test_flash);
> +
> +    size_t nb_configurations = sizeof configuration / sizeof 
> configuration[0];
> +    for (size_t i = 0; i < nb_configurations; ++i) {
> +        const FlashConfig *config = &configuration[i];
> +        char *path = g_strdup_printf("pflash-cfi02/%d",
> +                                     config->bank_width);
> +        qtest_add_data_func(path, config, test_flash);
> +        g_free(path);
> +    }
>      int result = g_test_run();
>      cleanup(NULL);
>      return result;
> --
> 2.20.1
>
>