[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Qemu-devel] [PATCH 1/2] ACPI: Add definitions for the SPCR table
From: |
Shannon Zhao |
Subject: |
Re: [Qemu-devel] [PATCH 1/2] ACPI: Add definitions for the SPCR table |
Date: |
Tue, 9 Jun 2015 18:53:08 +0800 |
User-agent: |
Mozilla/5.0 (Windows NT 6.1; rv:24.0) Gecko/20100101 Thunderbird/24.4.0 |
Hi Andrew,
Some minor comments below. Use scripts/checkpatch.pl before submitting.
On 2015/6/8 22:00, Andrew Jones wrote:
> SPCR is the Serial Port Console Redirection table. See the document
> linked from http://uefi.org/acpi. For serial port types, "Interface
> Type", see the documentation for the Debug Port Table 2 (DBG2).
>
> Signed-off-by: Andrew Jones <address@hidden>
> ---
> include/hw/acpi/acpi-defs.h | 72
> +++++++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 72 insertions(+)
>
> diff --git a/include/hw/acpi/acpi-defs.h b/include/hw/acpi/acpi-defs.h
> index 59cf277434b37..e579d4c509fc8 100644
> --- a/include/hw/acpi/acpi-defs.h
> +++ b/include/hw/acpi/acpi-defs.h
> @@ -197,6 +197,78 @@ enum {
> };
>
> /*
> + * ACPI Serial Port Console Redirection Table
> + */
> +enum {
> + ACPI_SERIAL_16550_COMPAT = 0,
> + ACPI_SERIAL_16550_SUBSET_COMPAT = 1,
> + ACPI_SERIAL_ARM_PL011_UART = 3,
> +};
> +
> +enum {
> + ACPI_SERIAL_ITYPE_PC = 1,
> + ACPI_SERIAL_ITYPE_APIC = 2,
> + ACPI_SERIAL_ITYPE_SAPIC = 4,
> + ACPI_SERIAL_ITYPE_ARMH_GIC = 8,
> +};
> +
> +enum {
> + ACPI_SERIAL_BAUD_9600 = 3,
> + ACPI_SERIAL_BAUD_19200 = 4,
> + ACPI_SERIAL_BAUD_57600 = 6,
> + ACPI_SERIAL_BAUD_115200 = 7,
> +};
> +
> +enum {
> + ACPI_SERIAL_FLOW_DCD_REQUIRED = 1,
> + ACPI_SERIAL_FLOW_HW = 2,
> + ACPI_SERIAL_FLOW_SW = 4,
> +};
> +
> +enum {
> + ACPI_SERIAL_TERM_VT100 = 0,
> + ACPI_SERIAL_TERM_VT100_PLUS = 1,
> + ACPI_SERIAL_TERM_VT_UTF8 = 2,
> + ACPI_SERIAL_TERM_ANSI = 3,
> +};
> +
> +struct AcpiSerialPortConsoleRedirection
> +{
open brace '{' following struct go on the same line
> + ACPI_TABLE_HEADER_DEF /* ACPI common table header */
> + uint8_t interface_type; /* See ACPI_SERIAL_ enums */
> + uint8_t reserved1[3]; /* Reserved, must be 0 */
> + struct AcpiGenericAddress base_address;
> + uint8_t interrupt_types; /* Interrupt type support mask,
> + * see ACPI_SERIAL_ITYPE_ enums */
> + uint8_t irq; /* PC irq used. 0 if
> ACPI_SERIAL_ITYPE_PC
> + * is not set, else must be one of
> + * 2-7,9-12,14-15 */
> + uint32_t gsi; /* Not valid if only
> ACPI_SERIAL_ITYPE_PC
> + * is set in the interrupt_types mask */
> + uint8_t baud; /* See ACPI_SERIAL_BAUD_ enums */
> + uint8_t parity; /* 0 = no parity, 1-255 reserved */
> + uint8_t stopbits; /* Must be 1 */
> + uint8_t flowctrl; /* See ACPI_SERIAL_FLOW_ enums */
> + uint8_t term_type; /* See ACPI_SERIAL_TERM_ enums */
> + uint8_t reserved2; /* Reserved, must be 0 */
> + uint16_t pci_device_id; /* 0xffff, if not a pci dev */
> + uint16_t pci_vendor_id; /* 0xffff, if not a pci dev */
> + uint8_t pci_bus; /* PCI bus number, 0 if not a pci dev */
> + uint8_t pci_slot; /* PCI slot number, 0 if not a pci dev
> */
> + uint8_t pci_func; /* PCI function num, 0 if not a pci dev
> */
> + uint32_t pci_flags; /* PCI compatibility mask,
> + * bits 1-31 reserved
> + * bit0 = 0, if not a pci dev
> + * bit0 = 1, don't suppress PNP or
> + * power management
> + */
> + uint8_t pci_seg; /* PCI segment number, 0 for systems
> + with less than 255 PCI busses */
> + uint32_t reserved3; /* Reserved, must be 0 */
> +} QEMU_PACKED;
> +typedef struct AcpiSerialPortConsoleRedirection
> AcpiSerialPortConsoleRedirection;
line over 80 characters
> +
> +/*
> * ACPI 1.0 Root System Description Table (RSDT)
> */
> struct AcpiRsdtDescriptorRev1
>
--
Shannon