Re: [PATCH v3 3/6] ps2: accept 'Set Key Make and Break' commands

[Sven Schnelle]

Hi Philippe,

On Wed, Oct 23, 2019 at 01:08:35PM +0200, Philippe Mathieu-Daudé wrote:
> Hi Sven,
> 
> (Please Cc reviewers who previously commented your patch)
>
> On 10/22/19 10:59 PM, Sven Schnelle wrote:
> > HP-UX sends both the 'Set key make and break (0xfc) and
> > 'Set all key typematic make and break' (0xfa). QEMU response
> > with 'Resend' as it doesn't handle these commands. HP-UX than
> > reports an PS/2 max retransmission exceeded error. Add these
> > commands and just reply with ACK.
> > 
> > Signed-off-by: Sven Schnelle <address@hidden>
> > ---
> >   hw/input/ps2.c | 10 ++++++++++
> >   1 file changed, 10 insertions(+)
> > 
> > diff --git a/hw/input/ps2.c b/hw/input/ps2.c
> > index 67f92f6112..0b671b6339 100644
> > --- a/hw/input/ps2.c
> > +++ b/hw/input/ps2.c
> > @@ -49,6 +49,8 @@
> >   #define KBD_CMD_RESET_DISABLE     0xF5    /* reset and disable scanning */
> >   #define KBD_CMD_RESET_ENABLE      0xF6    /* reset and enable scanning */
> >   #define KBD_CMD_RESET             0xFF    /* Reset */
> > +#define KBD_CMD_SET_MAKE_BREAK  0xFC    /* Set Make and Break mode */
> > +#define KBD_CMD_SET_TYPEMATIC   0xFA    /* Set Typematic Make and Break 
> > mode */
> >   /* Keyboard Replies */
> >   #define KBD_REPLY_POR             0xAA    /* Power on reset */
> > @@ -573,6 +575,7 @@ void ps2_write_keyboard(void *opaque, int val)
> >           case KBD_CMD_SCANCODE:
> >           case KBD_CMD_SET_LEDS:
> >           case KBD_CMD_SET_RATE:
> > +        case KBD_CMD_SET_MAKE_BREAK:
> 
> OK
> 
> >               s->common.write_cmd = val;
> >               ps2_queue(&s->common, KBD_REPLY_ACK);
> >               break;
> > @@ -592,11 +595,18 @@ void ps2_write_keyboard(void *opaque, int val)
> >                   KBD_REPLY_ACK,
> >                   KBD_REPLY_POR);
> >               break;
> > +        case KBD_CMD_SET_TYPEMATIC:
> > +            ps2_queue(&s->common, KBD_REPLY_ACK);
> 
> I'm not sure, can't this loop?

I don't see how?

> Can you fold it with the '0x00' case?

Ok.

> > +            break;
> >           default:
> >               ps2_queue(&s->common, KBD_REPLY_RESEND);
> >               break;
> >           }
> >           break;
> > +    case KBD_CMD_SET_MAKE_BREAK:
> 
> We can reorder this one in the same case with:
> 
>     case KBD_CMD_SET_LEDS:
>     case KBD_CMD_SET_RATE:

Ok.

> > +        ps2_queue(&s->common, KBD_REPLY_ACK);
> > +        s->common.write_cmd = -1;
> > +        break;
> >       case KBD_CMD_SCANCODE:
> >           if (val == 0) {
> >               if (s->common.queue.count <= PS2_QUEUE_SIZE - 2) {
> > 
> 

Regards
Sven