[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[PULL 04/12] ast2600: Configure CNTFRQ at 1125MHz
From: |
Peter Maydell |
Subject: |
[PULL 04/12] ast2600: Configure CNTFRQ at 1125MHz |
Date: |
Fri, 20 Dec 2019 14:26:36 +0000 |
From: Andrew Jeffery <address@hidden>
This matches the configuration set by u-boot on the AST2600.
Signed-off-by: Andrew Jeffery <address@hidden>
Reviewed-by: Richard Henderson <address@hidden>
Reviewed-by: Cédric Le Goater <address@hidden>
Reviewed-by: Philippe Mathieu-Daudé <address@hidden>
Message-id: address@hidden
Signed-off-by: Peter Maydell <address@hidden>
---
hw/arm/aspeed_ast2600.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/hw/arm/aspeed_ast2600.c b/hw/arm/aspeed_ast2600.c
index be88005dab8..89e4b009504 100644
--- a/hw/arm/aspeed_ast2600.c
+++ b/hw/arm/aspeed_ast2600.c
@@ -250,6 +250,9 @@ static void aspeed_soc_ast2600_realize(DeviceState *dev,
Error **errp)
object_property_set_int(OBJECT(&s->cpu[i]), aspeed_calc_affinity(i),
"mp-affinity", &error_abort);
+ object_property_set_int(OBJECT(&s->cpu[i]), 1125000000, "cntfrq",
+ &error_abort);
+
/*
* TODO: the secondary CPUs are started and a boot helper
* is needed when using -kernel
--
2.20.1
- [PULL 00/12] target-arm queue, Peter Maydell, 2019/12/20
- [PULL 01/12] target/arm: Remove redundant scaling of nexttick, Peter Maydell, 2019/12/20
- [PULL 02/12] target/arm: Abstract the generic timer frequency, Peter Maydell, 2019/12/20
- [PULL 03/12] target/arm: Prepare generic timer for per-platform CNTFRQ, Peter Maydell, 2019/12/20
- [PULL 04/12] ast2600: Configure CNTFRQ at 1125MHz,
Peter Maydell <=
- [PULL 05/12] hw/arm/smmuv3: Apply address mask to linear strtab base address, Peter Maydell, 2019/12/20
- [PULL 06/12] hw/arm/smmuv3: Correct SMMU_BASE_ADDR_MASK value, Peter Maydell, 2019/12/20
- [PULL 07/12] hw/arm/smmuv3: Check stream IDs against actual table LOG2SIZE, Peter Maydell, 2019/12/20
- [PULL 08/12] hw/arm/smmuv3: Align stream table base address to table size, Peter Maydell, 2019/12/20
- [PULL 09/12] hw/arm/smmuv3: Use correct bit positions in EVT_SET_ADDR2 macro, Peter Maydell, 2019/12/20
- [PULL 10/12] hw/arm/smmuv3: Report F_STE_FETCH fault address in correct word position, Peter Maydell, 2019/12/20
- [PULL 11/12] target/arm: Display helpful message when hflags mismatch, Peter Maydell, 2019/12/20
- [PULL 12/12] arm/arm-powerctl: rebuild hflags after setting CP15 bits in arm_set_cpu_on(), Peter Maydell, 2019/12/20