[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: Properly quitting qemu immediately after failing migration
From: |
Dr. David Alan Gilbert |
Subject: |
Re: Properly quitting qemu immediately after failing migration |
Date: |
Mon, 29 Jun 2020 17:46:18 +0100 |
User-agent: |
Mutt/1.14.3 (2020-06-14) |
* Max Reitz (mreitz@redhat.com) wrote:
> On 29.06.20 17:41, Dr. David Alan Gilbert wrote:
> > * Max Reitz (mreitz@redhat.com) wrote:
> >> Hi,
> >>
> >> In an iotest, I’m trying to quit qemu immediately after a migration has
> >> failed. Unfortunately, that doesn’t seem to be possible in a clean way:
> >> migrate_fd_cleanup() runs only at some point after the migration state
> >> is already “failed”, so if I just wait for that “failed” state and
> >> immediately quit, some cleanup functions may not have been run yet.
> >
> > Yeh this is hard; I always take the end of migrate_fd_cleanup to be the
> > real end.
>
> Yes, unfortunately I don’t seem to have a way to look for that end. :(
>
> > It always happens on the main thread I think (it's done as a bh in some
> > cases).
> >
> >> This is a problem with dirty bitmap migration at least, because it
> >> increases the refcount on all block devices that are to be migrated, so
> >> if we don’t call the cleanup function before quitting, the refcount will
> >> stay elevated and bdrv_close_all() will hit an assertion because those
> >> block devices are still around after blk_remove_all_bs() and
> >> blockdev_close_all_bdrv_states().
> >>
> >> In practice this particular issue might not be that big of a problem,
> >> because it just means qemu aborts when the user intended to let it quit
> >> anyway. But on one hand I could imagine that there are other clean-up
> >> paths that should definitely run before qemu quits (although I don’t
> >> know), and on the other, it’s a problem for my test.
> >
> > 'quit' varies - there are a lot of incoming failures that just assert;
> > very few of them cause a clean exit (I think there are more clean ones
> > after Peter's work on restartable postcopy a year or two ago).
>
> Well, my problem is about the source side, where there is still a VM
> running that I would expect to be in a sane state even after a failed
> migration.
Oh! Source side; the source side I worry much more about; if the
destination implodes after a failed migration I'm not too worried - but
the source side *shall not* fail.
> > I do see the end of migrate_fd_cleanup calls the notifier list; but it's
> > not clear to me that it's alwyas going to see the first transition to
> > 'failed' at that point.
>
> What exactly do you mean? It appears to me that both query-status and
> the MIGRATION events signal the failed state before migrate_fd_cleanup()
> is invoked.
OK, I was getting confused between event sending and the notifiers; the
event happens a bit before. The state gets set to failed and then we
call fd_cleanup in most cases; the state is what query-status is keyed
off, and is also what causes the event to be sent.
> If you mean I could add a notifier to that list to do something™, I’m
> not sure what exactly it is I’d so.
Yeh, that's why the notifiers are there....
However, if you need to do some cleanup at the end of a migration, then
I think adding a call inside migrate_fd_cleanup is perfectly fine.
> My test can’t do it, because it’s
> an iotest, and even if it could, I suppose I’d want to wait until even
> after all notifiers have been invoked (which isn’t guaranteed if I’d add
> a notifier myself).
>
> >> I tried working around the problem for my test by waiting on “Unable to
> >> write” appearing on stderr, because that indicates that
> >> migrate_fd_cleanup()’s error_report_err() has been reached. But on one
> >> hand, that isn’t really nice, and on the other, it doesn’t even work
> >> when the failure is on the source side (because then there is no
> >> s->error for migrate_fd_cleanup() to report).
> >>
> >> In all, I’m asking:
> >> (1) Is there a nice solution for me now to delay quitting qemu until the
> >> failed migration has been fully resolved, including the clean-up?
> >
> > In vl.c, I added a call to migration_shutdown in qemu_cleanup - although
> > that seems to be mostly about cleaning up the *outgoing* side; you could
> > add some incoming cleanup there.
>
> So you mean waiting until migrate_fd_cleanup() has run? Maybe I’ll try
> that tomorrow, although I’d hoped I could get this done without having
> to modify the code base... (I.e., I’d hoped there would be some
> QMP-queriable flag somewhere that could tell me whether the
> migrate_fd_cleanup() has run)
Please be a little careful around there; i.e. try as far as possible not
to hang on dead block devices.
> >> (2) Isn’t it a problem if qemu crashes when you issue “quit” via QMP at
> >> the wrong time? Like, maybe lingering subprocesses when using “exec”?
> >
> > Yeh that should be cleaner, but isn't.
>
> :(
Randomly quitting is safer than it used to be (again that qemu_cleanup
code is what should make it so).
Dave
> OK then. Thanks for your insights!
>
> Max
>
--
Dr. David Alan Gilbert / dgilbert@redhat.com / Manchester, UK