RE: [PATCH v6 5/7] misc: Add versal-usb2-regs module

[Sai Pavan Boddu]

Hi Gerd,

Please ignore this

Regards,
Sai Pavan
> -----Original Message-----
> From: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
> Sent: Wednesday, September 16, 2020 5:11 PM
> To: Peter Maydell <peter.maydell@linaro.org>; Markus Armbruster
> <armbru@redhat.com>; 'Marc-André Lureau'
> <marcandre.lureau@redhat.com>; Paolo Bonzini <pbonzini@redhat.com>;
> Gerd Hoffmann <kraxel@redhat.com>; Edgar Iglesias <edgari@xilinx.com>;
> Francisco Eduardo Iglesias <figlesia@xilinx.com>
> Cc: qemu-devel@nongnu.org; Alistair Francis <alistair.francis@wdc.com>;
> Eduardo Habkost <ehabkost@redhat.com>; Ying Fang
> <fangying1@huawei.com>; 'Philippe Mathieu-Daudé'
> <philmd@redhat.com>; Vikram Garhwal <fnuv@xilinx.com>; Paul
> Zimmerman <pauldzim@gmail.com>; Sai Pavan Boddu
> <saipava@xilinx.com>
> Subject: [PATCH v6 5/7] misc: Add versal-usb2-regs module
> 
> This module emulates control registers of versal usb2 controller, this is
> added just to make guest happy. In general this module would control the
> phy-reset signal from usb controller, data coherency of the transactions,
> signals the host system errors received from controller.
> 
> Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
> Signed-off-by: Vikram Garhwal <fnu.vikram@xilinx.com>
> ---
>  hw/misc/meson.build                          |   1 +
>  hw/misc/xlnx-versal-usb2-ctrl-regs.c         | 221
> +++++++++++++++++++++++++++
>  include/hw/misc/xlnx-versal-usb2-ctrl-regs.h |  46 ++++++
>  3 files changed, 268 insertions(+)
>  create mode 100644 hw/misc/xlnx-versal-usb2-ctrl-regs.c
>  create mode 100644 include/hw/misc/xlnx-versal-usb2-ctrl-regs.h
> 
> diff --git a/hw/misc/meson.build b/hw/misc/meson.build index
> 793d45b..b336dd1 100644
> --- a/hw/misc/meson.build
> +++ b/hw/misc/meson.build
> @@ -109,3 +109,4 @@ specific_ss.add(when: 'CONFIG_MIPS_CPS', if_true:
> files('mips_cmgcr.c', 'mips_cp
>  specific_ss.add(when: 'CONFIG_MIPS_ITU', if_true: files('mips_itu.c'))
> 
>  specific_ss.add(when: 'CONFIG_SBSA_REF', if_true: files('sbsa_ec.c'))
> +specific_ss.add(when: 'CONFIG_XLNX_VERSAL', if_true:
> +files('xlnx-versal-usb2-ctrl-regs.c'))
> diff --git a/hw/misc/xlnx-versal-usb2-ctrl-regs.c b/hw/misc/xlnx-versal-usb2-
> ctrl-regs.c
> new file mode 100644
> index 0000000..6ddd38b
> --- /dev/null
> +++ b/hw/misc/xlnx-versal-usb2-ctrl-regs.c
> @@ -0,0 +1,221 @@
> +/*
> + * QEMU model of the XlnxUsb2Regs Register control block/Status for
> +USB2.0 IP
> + *
> + * This module should control phy_reset, permanent device plugs, frame
> +length
> + * time adjust & setting of coherency paths. None of which are emulated
> +in
> + * present model.
> + *
> + * Copyright (c) 2020 Xilinx Inc. Vikram Garhwal
> +<fnu.vikram@xilinx.com>
> + *
> + * Permission is hereby granted, free of charge, to any person
> +obtaining a copy
> + * of this software and associated documentation files (the
> +"Software"), to deal
> + * in the Software without restriction, including without limitation
> +the rights
> + * to use, copy, modify, merge, publish, distribute, sublicense, and/or
> +sell
> + * copies of the Software, and to permit persons to whom the Software
> +is
> + * furnished to do so, subject to the following conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> +included in
> + * all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY
> KIND,
> +EXPRESS OR
> + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
> +MERCHANTABILITY,
> + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO
> EVENT
> +SHALL
> + * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,
> DAMAGES OR
> +OTHER
> + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
> +ARISING FROM,
> + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
> +DEALINGS IN
> + * THE SOFTWARE.
> + */
> +
> +#include "qemu/osdep.h"
> +#include "hw/sysbus.h"
> +#include "hw/irq.h"
> +#include "hw/register.h"
> +#include "qemu/bitops.h"
> +#include "qemu/log.h"
> +#include "qom/object.h"
> +#include "migration/vmstate.h"
> +#include "hw/misc/xlnx-versal-usb2-ctrl-regs.h"
> +
> +#ifndef XILINX_USB2_REGS_ERR_DEBUG
> +#define XILINX_USB2_REGS_ERR_DEBUG 0
> +#endif
> +
> +REG32(BUS_FILTER, 0x30)
> +    FIELD(BUS_FILTER, BYPASS, 0, 4)
> +REG32(PORT, 0x34)
> +    FIELD(PORT, HOST_SMI_BAR_WR, 4, 1)
> +    FIELD(PORT, HOST_SMI_PCI_CMD_REG_WR, 3, 1)
> +    FIELD(PORT, HOST_MSI_ENABLE, 2, 1)
> +    FIELD(PORT, PWR_CTRL_PRSNT, 1, 1)
> +    FIELD(PORT, HUB_PERM_ATTACH, 0, 1)
> +REG32(JITTER_ADJUST, 0x38)
> +    FIELD(JITTER_ADJUST, FLADJ, 0, 6)
> +REG32(BIGENDIAN, 0x40)
> +    FIELD(BIGENDIAN, ENDIAN_GS, 0, 1)
> +REG32(COHERENCY, 0x44)
> +    FIELD(COHERENCY, USB_COHERENCY, 0, 1) REG32(XHC_BME, 0x48)
> +    FIELD(XHC_BME, XHC_BME, 0, 1)
> +REG32(REG_CTRL, 0x60)
> +    FIELD(REG_CTRL, SLVERR_ENABLE, 0, 1) REG32(IR_STATUS, 0x64)
> +    FIELD(IR_STATUS, HOST_SYS_ERR, 1, 1)
> +    FIELD(IR_STATUS, ADDR_DEC_ERR, 0, 1) REG32(IR_MASK, 0x68)
> +    FIELD(IR_MASK, HOST_SYS_ERR, 1, 1)
> +    FIELD(IR_MASK, ADDR_DEC_ERR, 0, 1)
> +REG32(IR_ENABLE, 0x6c)
> +    FIELD(IR_ENABLE, HOST_SYS_ERR, 1, 1)
> +    FIELD(IR_ENABLE, ADDR_DEC_ERR, 0, 1) REG32(IR_DISABLE, 0x70)
> +    FIELD(IR_DISABLE, HOST_SYS_ERR, 1, 1)
> +    FIELD(IR_DISABLE, ADDR_DEC_ERR, 0, 1) REG32(USB3, 0x78)
> +
> +static void ir_update_irq(XlnxUsb2Regs *s) {
> +    bool pending = s->regs[R_IR_STATUS] & ~s->regs[R_IR_MASK];
> +    qemu_set_irq(s->irq_ir, pending);
> +}
> +
> +static void ir_status_postw(RegisterInfo *reg, uint64_t val64) {
> +    XlnxUsb2Regs *s = XILINX_USB2_REGS(reg->opaque);
> +    /*
> +     * TODO: This should also clear USBSTS.HSE field in USB XHCI register.
> +     * May be combine both the modules.
> +     */
> +    ir_update_irq(s);
> +}
> +
> +static uint64_t ir_enable_prew(RegisterInfo *reg, uint64_t val64) {
> +    XlnxUsb2Regs *s = XILINX_USB2_REGS(reg->opaque);
> +    uint32_t val = val64;
> +
> +    s->regs[R_IR_MASK] &= ~val;
> +    ir_update_irq(s);
> +    return 0;
> +}
> +
> +static uint64_t ir_disable_prew(RegisterInfo *reg, uint64_t val64) {
> +    XlnxUsb2Regs *s = XILINX_USB2_REGS(reg->opaque);
> +    uint32_t val = val64;
> +
> +    s->regs[R_IR_MASK] |= val;
> +    ir_update_irq(s);
> +    return 0;
> +}
> +
> +static const RegisterAccessInfo usb2_regs_regs_info[] = {
> +    {   .name = "BUS_FILTER",  .addr = A_BUS_FILTER,
> +        .rsvd = 0xfffffff0,
> +    },{ .name = "PORT",  .addr = A_PORT,
> +        .rsvd = 0xffffffe0,
> +    },{ .name = "JITTER_ADJUST",  .addr = A_JITTER_ADJUST,
> +        .reset = 0x20,
> +        .rsvd = 0xffffffc0,
> +    },{ .name = "BIGENDIAN",  .addr = A_BIGENDIAN,
> +        .rsvd = 0xfffffffe,
> +    },{ .name = "COHERENCY",  .addr = A_COHERENCY,
> +        .rsvd = 0xfffffffe,
> +    },{ .name = "XHC_BME",  .addr = A_XHC_BME,
> +        .reset = 0x1,
> +        .rsvd = 0xfffffffe,
> +    },{ .name = "REG_CTRL",  .addr = A_REG_CTRL,
> +        .rsvd = 0xfffffffe,
> +    },{ .name = "IR_STATUS",  .addr = A_IR_STATUS,
> +        .rsvd = 0xfffffffc,
> +        .w1c = 0x3,
> +        .post_write = ir_status_postw,
> +    },{ .name = "IR_MASK",  .addr = A_IR_MASK,
> +        .reset = 0x3,
> +        .rsvd = 0xfffffffc,
> +        .ro = 0x3,
> +    },{ .name = "IR_ENABLE",  .addr = A_IR_ENABLE,
> +        .rsvd = 0xfffffffc,
> +        .pre_write = ir_enable_prew,
> +    },{ .name = "IR_DISABLE",  .addr = A_IR_DISABLE,
> +        .rsvd = 0xfffffffc,
> +        .pre_write = ir_disable_prew,
> +    },{ .name = "USB3",  .addr = A_USB3,
> +    }
> +};
> +
> +static void usb2_regs_reset(DeviceState *dev) {
> +    XlnxUsb2Regs *s = XILINX_USB2_REGS(dev);
> +    unsigned int i;
> +
> +    for (i = 0; i < ARRAY_SIZE(s->regs_info); ++i) {
> +        register_reset(&s->regs_info[i]);
> +    }
> +
> +    ir_update_irq(s);
> +}
> +
> +static const MemoryRegionOps usb2_regs_ops = {
> +    .read = register_read_memory,
> +    .write = register_write_memory,
> +    .endianness = DEVICE_LITTLE_ENDIAN,
> +    .valid = {
> +        .min_access_size = 4,
> +        .max_access_size = 4,
> +    },
> +};
> +
> +static void usb2_regs_init(Object *obj) {
> +    XlnxUsb2Regs *s = XILINX_USB2_REGS(obj);
> +    SysBusDevice *sbd = SYS_BUS_DEVICE(obj);
> +    RegisterInfoArray *reg_array;
> +
> +    memory_region_init(&s->iomem, obj, TYPE_XILINX_USB2_REGS,
> +                       USB2_REGS_R_MAX * 4);
> +    reg_array =
> +        register_init_block32(DEVICE(obj), usb2_regs_regs_info,
> +                              ARRAY_SIZE(usb2_regs_regs_info),
> +                              s->regs_info, s->regs,
> +                              &usb2_regs_ops,
> +                              XILINX_USB2_REGS_ERR_DEBUG,
> +                              USB2_REGS_R_MAX * 4);
> +    memory_region_add_subregion(&s->iomem,
> +                                0x0,
> +                                &reg_array->mem);
> +    sysbus_init_mmio(sbd, &s->iomem);
> +    sysbus_init_irq(sbd, &s->irq_ir);
> +}
> +
> +static const VMStateDescription vmstate_usb2_regs = {
> +    .name = TYPE_XILINX_USB2_REGS,
> +    .version_id = 1,
> +    .minimum_version_id = 1,
> +    .fields = (VMStateField[]) {
> +        VMSTATE_UINT32_ARRAY(regs, XlnxUsb2Regs, USB2_REGS_R_MAX),
> +        VMSTATE_END_OF_LIST(),
> +    }
> +};
> +
> +static void usb2_regs_class_init(ObjectClass *klass, void *data) {
> +    DeviceClass *dc = DEVICE_CLASS(klass);
> +
> +    dc->reset = usb2_regs_reset;
> +    dc->vmsd = &vmstate_usb2_regs;
> +}
> +
> +static const TypeInfo usb2_regs_info = {
> +    .name          = TYPE_XILINX_USB2_REGS,
> +    .parent        = TYPE_SYS_BUS_DEVICE,
> +    .instance_size = sizeof(XlnxUsb2Regs),
> +    .class_init    = usb2_regs_class_init,
> +    .instance_init = usb2_regs_init,
> +};
> +
> +static void usb2_regs_register_types(void) {
> +    type_register_static(&usb2_regs_info);
> +}
> +
> +type_init(usb2_regs_register_types)
> diff --git a/include/hw/misc/xlnx-versal-usb2-ctrl-regs.h
> b/include/hw/misc/xlnx-versal-usb2-ctrl-regs.h
> new file mode 100644
> index 0000000..1d75f63
> --- /dev/null
> +++ b/include/hw/misc/xlnx-versal-usb2-ctrl-regs.h
> @@ -0,0 +1,46 @@
> +/*
> + * QEMU model of the XlnxUsb2Regs Register control block/Status for
> +USB2.0 IP
> + *
> + * Copyright (c) 2020 Xilinx Inc.
> + *
> + * Autogenerated by xregqemu.py 2020-04-08.
> + *
> + * Permission is hereby granted, free of charge, to any person
> +obtaining a copy
> + * of this software and associated documentation files (the
> +"Software"), to deal
> + * in the Software without restriction, including without limitation
> +the rights
> + * to use, copy, modify, merge, publish, distribute, sublicense, and/or
> +sell
> + * copies of the Software, and to permit persons to whom the Software
> +is
> + * furnished to do so, subject to the following conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> +included in
> + * all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY
> KIND,
> +EXPRESS OR
> + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
> +MERCHANTABILITY,
> + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO
> EVENT
> +SHALL
> + * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,
> DAMAGES OR
> +OTHER
> + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
> +ARISING FROM,
> + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
> +DEALINGS IN
> + * THE SOFTWARE.
> + */
> +
> +#ifndef _XLNX_USB2_REGS_H_
> +#define _XLNX_USB2_REGS_H_
> +
> +#define TYPE_XILINX_USB2_REGS "xlnx.versal-usb2-ctrl-regs"
> +
> +#define XILINX_USB2_REGS(obj) \
> +     OBJECT_CHECK(XlnxUsb2Regs, (obj), TYPE_XILINX_USB2_REGS)
> +
> +#define USB2_REGS_R_MAX ((0x78 / 4) + 1)
> +
> +typedef struct XlnxUsb2Regs {
> +    SysBusDevice parent_obj;
> +    MemoryRegion iomem;
> +    qemu_irq irq_ir;
> +
> +    uint32_t regs[USB2_REGS_R_MAX];
> +    RegisterInfo regs_info[USB2_REGS_R_MAX]; } XlnxUsb2Regs;
> +
> +#endif
> --
> 2.7.4