qemu-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[PATCH v2 06/12] aspeed/smc: Wire CS lines at reset


From: Cédric Le Goater
Subject: [PATCH v2 06/12] aspeed/smc: Wire CS lines at reset
Date: Wed, 7 Jun 2023 06:39:37 +0200

Currently, a set of default flash devices is created at machine init
and drives defined on the QEMU command line are associated to the FMC
and SPI controllers in sequence :

   -drive file<file>,format=raw,if=mtd
   -drive file<file1>,format=raw,if=mtd

The CS lines are wired in the same creation loop. This makes a strong
assumption on the ordering and is not very flexible since only a
limited set of flash devices can be defined : 1 FMC + 1 or 2 SPI,
which is less than what the SoC really supports.

A better alternative would be to define the flash devices on the
command line using a blockdev attached to a CS line of a SSI bus :

    -blockdev node-name=fmc0,driver=file,filename=./flash.img
    -device mx66u51235f,addr=0x0,bus=ssi.0,drive=fmc0

However, user created flash devices are not correctly wired to their
SPI controller and consequently can not be used by the machine. Fix
that and wire the CS lines of all available devices when the SSI bus
is reset.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
---
 hw/arm/aspeed.c     | 5 +----
 hw/ssi/aspeed_smc.c | 8 ++++++++
 2 files changed, 9 insertions(+), 4 deletions(-)

diff --git a/hw/arm/aspeed.c b/hw/arm/aspeed.c
index 76a1e7303de1..e5a49bb0b1a7 100644
--- a/hw/arm/aspeed.c
+++ b/hw/arm/aspeed.c
@@ -299,17 +299,14 @@ void aspeed_board_init_flashes(AspeedSMCState *s, const 
char *flashtype,
 
     for (i = 0; i < count; ++i) {
         DriveInfo *dinfo = drive_get(IF_MTD, 0, unit0 + i);
-        qemu_irq cs_line;
         DeviceState *dev;
 
         dev = qdev_new(flashtype);
         if (dinfo) {
             qdev_prop_set_drive(dev, "drive", blk_by_legacy_dinfo(dinfo));
         }
+        qdev_prop_set_uint8(dev, "addr", i);
         qdev_realize_and_unref(dev, BUS(s->spi), &error_fatal);
-
-        cs_line = qdev_get_gpio_in_named(dev, SSI_GPIO_CS, 0);
-        qdev_connect_gpio_out_named(DEVICE(s), "cs", i, cs_line);
     }
 }
 
diff --git a/hw/ssi/aspeed_smc.c b/hw/ssi/aspeed_smc.c
index 72811693224d..2a4001b774a2 100644
--- a/hw/ssi/aspeed_smc.c
+++ b/hw/ssi/aspeed_smc.c
@@ -692,6 +692,14 @@ static void aspeed_smc_reset(DeviceState *d)
         memset(s->regs, 0, sizeof s->regs);
     }
 
+    for (i = 0; i < asc->cs_num_max; i++) {
+        DeviceState *dev = ssi_get_cs(s->spi, i);
+        if (dev) {
+            qemu_irq cs_line = qdev_get_gpio_in_named(dev, SSI_GPIO_CS, 0);
+            qdev_connect_gpio_out_named(DEVICE(s), "cs", i, cs_line);
+        }
+    }
+
     /* Unselect all peripherals */
     for (i = 0; i < asc->cs_num_max; ++i) {
         s->regs[s->r_ctrl0 + i] |= CTRL_CE_STOP_ACTIVE;
-- 
2.40.1




reply via email to

[Prev in Thread] Current Thread [Next in Thread]