Re: [qemu-s390x] [PATCH v4] s390: diagnose 318 info reset and migration support

[Cornelia Huck]

On Mon, 13 May 2019 13:34:35 +0200
David Hildenbrand <address@hidden> wrote:

> On 13.05.19 12:55, Christian Borntraeger wrote:
> > 
> > 
> > On 13.05.19 11:57, David Hildenbrand wrote:  
> >> On 13.05.19 11:51, Christian Borntraeger wrote:  
> >>>
> >>>
> >>> On 13.05.19 11:40, David Hildenbrand wrote:  
> >>>> On 13.05.19 11:34, Christian Borntraeger wrote:  
> >>>>>
> >>>>>
> >>>>> On 13.05.19 10:03, David Hildenbrand wrote:  
> >>>>>>>> +    if ((SCCB_SIZE - sizeof(ReadInfo)) / sizeof(CPUEntry) < 
> >>>>>>>> S390_MAX_CPUS)
> >>>>>>>> +        mc->max_cpus = S390_MAX_CPUS - 8;  
> >>>>>>>
> >>>>>>> This is too complicated, just set it always to 240.
> >>>>>>>
> >>>>>>> However, I am still not sure how to best handle this scenario. One
> >>>>>>> solution is
> >>>>>>>
> >>>>>>> 1. Set it statically to 240 for machine > 4.1
> >>>>>>> 2. Keep the old machines unmodifed
> >>>>>>> 3. Don't indicate the CPU feature for machines <= 4.0
> >>>>>>>
> >>>>>>> #3 is the problematic part, as it mixes host CPU features and 
> >>>>>>> machines.
> >>>>>>> Bad. The host CPU model should always look the same on all machines. I
> >>>>>>> don't like this.
> >>>>>>>  
> >>>>>>
> >>>>>> FWIW, #3 is only an issue when modeling it via the CPU model, like
> >>>>>> Christian suggested.
> >>>>>>
> >>>>>> I suggest the following
> >>>>>>
> >>>>>> 1. Set the max #cpus for 4.1 to 240 (already done)
> >>>>>> 2. Keep it for the other machines unmodified (as suggested by Thomas)
> >>>>>> 3. Create the layout of the SCCB depending on the machine type (to be 
> >>>>>> done)
> >>>>>>
> >>>>>> If we want to model diag318 via a CPU feature (which makes sense for
> >>>>>> migration):
> >>>>>>
> >>>>>> 4. Disable diag318 with a warning if used with a machine < 4.1
> >>>>>>  
> >>>>>
> >>>>> I think there is a simpler solution. It is perfectly fine to fail the 
> >>>>> startup
> >>>>> if we cannot fulfil the cpu model. So lets just allow 248 and allow 
> >>>>> this feature 
> >>>>> also for older machines. And if somebody chooses both at the same time,
> >>>>> lets fails the startup.  
> >>>>
> >>>> To which knob do you want to glue the layout of the SCLP response? Like
> >>>> I described?  Do you mean instead of warning and masking the feature off
> >>>> as I suggested, simply failing?  
> >>>
> >>> The sclp response will depend on the dia318 cpu model flag. If its on, 
> >>> the sclp
> >>> response will have it, otherwise not.
> >>> - host-passthrough: not migration safe anyway
> >>> - host-model: if the target has diag318 good, otherwise we reject 
> >>> migration   
> >>>>
> >>>> In that case, -machine ..-4.0 -cpu host will not work on new HW with new
> >>>> KVM. Just noting.  
> >>>
> >>> Only if you have 248 CPUs (which is unlikely). My point was to do that 
> >>> for all
> >>> machine levels.
> >>>  
> >>
> >> The issue with this approach is that e.g. libvirt is not aware of this
> >> restriction. It could query "max_cpus" and expand the host-cpu model,
> >> but starting a guest with > 240 cpus would fail. Maybe this is acceptable. 
> >>  
> > 
> > As of today we do the cpu model check in the same way. libvirt actually 
> > tries
> > to run QEMU and handles failures.
> > 
> > For a failure, the user still has still to use >240 CPUs in its XML. The 
> > only downside
> > is that libvirt will not reject this right away.
> > 
> > During startup we would then print an error message like
> > 
> > "The diag318 cpu feature is only supported for 240 and less CPUs."
> > 
> > This is of similar quality as
> > "Selected CPU GA level is too new. Maximum supported model in the 
> > configuration: \'%s\'",
> >   
> 
> But that can be tested using the runability information if I am not wrong.

You mean the cpu level information, right?

> 
> > and others that we have today.
> > 
> > So yes, I think this would be acceptable.  
> 
> I guess it is acceptable yes. I doubt anybody uses that many CPUs in
> production either way. But you never know.

I think that using that many cpus is a more uncommon setup, but I still
think that having to wait for actual failure is worse than being able
to find out beforehand. Any way to make this discoverable?