Re: [PATCH] pc-bios/s390x: Pack ResetInfo struct

[Thomas Huth]

On 06/02/2020 11.09, Christian Borntraeger wrote:
> 
> 
> On 05.02.20 19:21, Jason J. Herne wrote:
>> This fixes vfio-ccw when booting non-Linux operating systems. Without this
>> struct being packed, a few extra bytes of low core memory get overwritten 
>> when
>> we  assign a value to memory address 0 in jump_to_IPL_2. This is enough to
>> cause some non-Linux OSes of fail when booting.
>>
>> The problem was introduced by:
>> 5c6f0d5f46a77d77 "pc-bios/s390x: Fix reset psw mask".
>>
>> The fix is to pack the struct thereby removing the 4 bytes of padding that 
>> get
>> added at the end, likely to allow an array of these structs to naturally 
>> align
>> on an 8-byte boundary.
>>
>> Fixes: 5c6f0d5f46a7 ("pc-bios/s390x: Fix reset psw mask")
>> CC: Janosch Frank <address@hidden>
>> Signed-off-by: Jason J. Herne <address@hidden>
>> ---
>>  pc-bios/s390-ccw/jump2ipl.c | 2 +-
>>  1 file changed, 1 insertion(+), 1 deletion(-)
>>
>> diff --git a/pc-bios/s390-ccw/jump2ipl.c b/pc-bios/s390-ccw/jump2ipl.c
>> index da13c43cc0..1e9eaa037f 100644
>> --- a/pc-bios/s390-ccw/jump2ipl.c
>> +++ b/pc-bios/s390-ccw/jump2ipl.c
>> @@ -18,7 +18,7 @@
>>  typedef struct ResetInfo {
>>      uint64_t ipl_psw;
>>      uint32_t ipl_continue;
>> -} ResetInfo;
>> +} __attribute__((packed)) ResetInfo;
>>  
>>  static ResetInfo save;
> 
> Just looked into that.
> 
> We do save the old content in "save" and restore the old memory content.
> 
> static void jump_to_IPL_2(void)
> {
>     ResetInfo *current = 0;
> 
>     void (*ipl)(void) = (void *) (uint64_t) current->ipl_continue;
> --->*current = save;
>     ipl(); /* should not return */
> }
> 
> void jump_to_IPL_code(uint64_t address)
> {
>     /* store the subsystem information _after_ the bootmap was loaded */
>     write_subsystem_identification();
> 
>     /* prevent unknown IPL types in the guest */
>     if (iplb.pbt == S390_IPL_TYPE_QEMU_SCSI) {
>         iplb.pbt = S390_IPL_TYPE_CCW;
>         set_iplb(&iplb);
>     }
> 
>     /*
>      * The IPL PSW is at address 0. We also must not overwrite the
>      * content of non-BIOS memory after we loaded the guest, so we
>      * save the original content and restore it in jump_to_IPL_2.
>      */
>     ResetInfo *current = 0;
> 
> --->save = *current;

Right, and this should also work without your modification. I've stared
at the code a couple of weeks ago, looking for a very similar issue:

 https://lists.gnu.org/archive/html/qemu-devel/2019-12/msg03484.html

... but in the end, the problem was something else:

 https://lists.gnu.org/archive/html/qemu-devel/2019-12/msg03520.html

and the fix had been done in the startup code of the test:

 https://lists.gnu.org/archive/html/qemu-devel/2019-12/msg04225.html

So I'd guess that you face the very same problem here. That means, you
either have to convince the non-Linux OS to check their startup code
whether they depend on zeroed registers somewhere, or we fix this issue
for good in jump_to_IPL_2() by clearing the registers there before
jumping into the OS code (which we likely should do anyway since the OS
may expect a clean state).

 Thomas