[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Freeipmi-devel] fiid_obj_get: maximum_privilege_for_cipher_suite_3
From: |
Al Chu |
Subject: |
Re: [Freeipmi-devel] fiid_obj_get: maximum_privilege_for_cipher_suite_3: no data set |
Date: |
Mon, 15 Nov 2010 15:55:05 -0800 |
Hi Peter,
Assuming you're using a recent version of FreeIPMI, there's probably
some IPMI non-compliance going on on your motherboard. The short guess
is that the motherboard isn't properly reporting things to bmc-config
correctly, and bmc-config gets confused and gives up. There's been a
few IPMI issues for the HP DL145 already reported to me. Lets see if we
can figure out what's going on. Can you send me the --debug output.
Since the problem appears just in that section, how about running this
to shorten the output
bmc-config --checkout --section=Rmcpplus_Conf_Privilege --debug
> Any idea what could be wrong, or how to fix it? And could this be the
> reason the network won't come up?
Although it's always possible, it's unlikely this is the cause of IPMI
over LAN not working. Can you get an ipmiping (/usr/sbin/ipmiping) to
work? If yes that would point to it being an authentication problem
(e.g. username/password/privilege, etc.), if no, possibly a more basic
networking issue (subnetting, routing, etc.).
I haven't played with this motherboard specifically, but a few recent
ones I've encountered require you to hard-reset (e.g. power button push)
the motherboard for configuration changes to "stick". It certainly
can't hurt to try.
Al
On Mon, 2010-11-15 at 15:29 -0800, Peter Selby wrote:
> Hi guys,
>
> I'm trying to configure the BMC on an HP ProLiant DL145 G2 using
> bmc-config. IPMI over LAN is not working; it should have a fixed IP,
> but it won't respond to anything.
>
> When I try to dump the BMC config, I get:
>
> $ bmc-config --checkout
> ...
> Section Rmcpplus_Conf_Privilege
> fiid_obj_get: maximum_privilege_for_cipher_suite_3: no data set
> $
>
> Everything prior to that dumps okay. Adding the section (and
> subsequent SOL_Conf section) manually, I get two possible results:
>
> * Empty Rmcpplus_Conf_Privilege: Config commits successfully, but a
> checkout results in the same problem
> * Rmcpplus_Conf_Privilege filled in based on the bmc-config.conf
> manpage (with Maximum_Privilege_Cipher_Suite_Id_0-through-4 or 12): I
> get the same error, fiid_obj_get:
> maximum_privilege_for_cipher_suite_3: no data set
>
> Any idea what could be wrong, or how to fix it? And could this be the
> reason the network won't come up?
>
> Thanks,
>
> Peter
>
> _______________________________________________
> Freeipmi-devel mailing list
> address@hidden
> http://BLOCKEDlists.gnu.org/mailman/listinfo/freeipmi-devel
>
--
Albert Chu
address@hidden
Computer Scientist
High Performance Systems Division
Lawrence Livermore National Laboratory
- [Freeipmi-devel] fiid_obj_get: maximum_privilege_for_cipher_suite_3: no data set, Peter Selby, 2010/11/15
- Re: [Freeipmi-devel] fiid_obj_get: maximum_privilege_for_cipher_suite_3: no data set,
Al Chu <=
- Message not available
- Re: [Freeipmi-devel] fiid_obj_get: maximum_privilege_for_cipher_suite_3: no data set, Al Chu, 2010/11/15
- Message not available
- Re: [Freeipmi-devel] fiid_obj_get: maximum_privilege_for_cipher_suite_3: no data set, Al Chu, 2010/11/16
- [Freeipmi-devel] Set Boot Device Parameter in ipmi-chassis-config, Liebig, Holger, 2010/11/17
- Re: [Freeipmi-devel] Set Boot Device Parameter in ipmi-chassis-config, Al Chu, 2010/11/17
- RE: [Freeipmi-devel] Set Boot Device Parameter in ipmi-chassis-config, Liebig, Holger, 2010/11/18
- RE: [Freeipmi-devel] Set Boot Device Parameter in ipmi-chassis-config, Al Chu, 2010/11/18
- RE: [Freeipmi-devel] Set Boot Device Parameter in ipmi-chassis-config, Liebig, Holger, 2010/11/22
- Message not available
- Re: [Freeipmi-devel] fiid_obj_get: maximum_privilege_for_cipher_suite_3: no data set, Al Chu, 2010/11/16
- Re: [Freeipmi-devel] fiid_obj_get: maximum_privilege_for_cipher_suite_3: no data set, Al Chu, 2010/11/17
- Message not available
- Message not available
- Re: [Freeipmi-devel] fiid_obj_get: maximum_privilege_for_cipher_suite_3: no data set, Al Chu, 2010/11/17