[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Freeipmi-users] Missing details on HP Proliant DL380 G7
From: |
Christopher Maestas |
Subject: |
Re: [Freeipmi-users] Missing details on HP Proliant DL380 G7 |
Date: |
Tue, 22 Mar 2011 16:52:46 -0600 |
Hello,
One of the most recent things I found is that some readings come out on HP
ilo3 with ipmitool versus freeipmi ... For example:
# ipmitool -H HOST -U USER -P PASSWORD -I lanplus sdr
UID Light | 0 unspecified | ok
Sys. Health LED | 0 unspecified | ok
Power Supply 1 | 170 Watts | nc
Power Supply 2 | 155 Watts | nc
Power Supply 3 | disabled | ns
Power Supply 4 | disabled | ns
Power Supplies | 0 unspecified | nc
Fan 1 | 42.34 unspecifi | nc
Fan 2 | 42.34 unspecifi | nc
Fan 3 | 42.34 unspecifi | nc
Fan 4 | 42.34 unspecifi | nc
Fans | 0 unspecified | nc
Temp 1 | 18 degrees C | ok
Temp 2 | 45 degrees C | ok
Temp 3 | 47 degrees C | ok
Temp 4 | 46 degrees C | ok
Temp 5 | 42 degrees C | ok
Temp 6 | 35 degrees C | ok
Temp 7 | 30 degrees C | ok
Temp 8 | 32 degrees C | ok
Temp 9 | 30 degrees C | ok
Temp 10 | 32 degrees C | ok
Temp 11 | 30 degrees C | ok
Temp 12 | 31 degrees C | ok
Temp 13 | 28 degrees C | ok
Temp 14 | 30 degrees C | ok
Temp 15 | 28 degrees C | ok
Temp 16 | 32 degrees C | ok
Temp 17 | 27 degrees C | ok
Temp 18 | 30 degrees C | ok
Temp 19 | 28 degrees C | ok
Temp 20 | 28 degrees C | ok
Temp 21 | 28 degrees C | ok
Temp 22 | 32 degrees C | ok
Temp 23 | 45 degrees C | ok
Temp 24 | 29 degrees C | ok
Temp 25 | 37 degrees C | ok
Temp 26 | 41 degrees C | ok
Temp 27 | 49 degrees C | ok
Temp 28 | 73 degrees C | ok
Temp 29 | 67 degrees C | ok
Temp 30 | 37 degrees C | ok
Temp 31 | 37 degrees C | ok
Temp 32 | 32 degrees C | ok
Temp 33 | disabled | ns
Temp 34 | disabled | ns
Temp 35 | disabled | ns
Temp 36 | disabled | ns
Memory | 0 error | ok
Power Meter | 462 Watts | cr
ipmi-sensors wasn't picking up this data ...
---
# ipmi-sensors -h HOST
ID | Name | Type | Reading | Units | Event
0 | UID Light | OEM Reserved | N/A | N/A | 'OEM Event =
0000h'
1 | Sys. Health LED | OEM Reserved | N/A | N/A | 'OEM Event =
0000h'
2 | Power Supply 1 | Power Supply | N/A | N/A | 'Presence
detected'
3 | Power Supply 2 | Power Supply | N/A | N/A | 'Presence
detected'
4 | Power Supply 3 | Power Supply | N/A | N/A | N/A
5 | Power Supply 4 | Power Supply | N/A | N/A | N/A
6 | Power Supplies | Power Supply | N/A | N/A | 'Fully Redundant'
8 | Fan 1 | Fan | N/A | N/A | 'transition to
Running'
9 | Fan 2 | Fan | N/A | N/A | 'transition to
Running'
10 | Fan 3 | Fan | N/A | N/A | 'transition to
Running'
11 | Fan 4 | Fan | N/A | N/A | 'transition to
Running'
12 | Fans | Fan | N/A | N/A | 'Fully Redundant'
14 | Temp 1 | Temperature | 18.00 | C | 'OK'
15 | Temp 2 | Temperature | 45.00 | C | 'OK'
16 | Temp 3 | Temperature | 47.00 | C | 'OK'
17 | Temp 4 | Temperature | 47.00 | C | 'OK'
18 | Temp 5 | Temperature | 41.00 | C | 'OK'
19 | Temp 6 | Temperature | 35.00 | C | 'OK'
20 | Temp 7 | Temperature | 31.00 | C | 'OK'
21 | Temp 8 | Temperature | 32.00 | C | 'OK'
22 | Temp 9 | Temperature | 30.00 | C | 'OK'
23 | Temp 10 | Temperature | 32.00 | C | 'OK'
24 | Temp 11 | Temperature | 30.00 | C | 'OK'
25 | Temp 12 | Temperature | 30.00 | C | 'OK'
26 | Temp 13 | Temperature | 28.00 | C | 'OK'
27 | Temp 14 | Temperature | 30.00 | C | 'OK'
28 | Temp 15 | Temperature | 28.00 | C | 'OK'
29 | Temp 16 | Temperature | 32.00 | C | 'OK'
30 | Temp 17 | Temperature | 26.00 | C | 'OK'
31 | Temp 18 | Temperature | 30.00 | C | 'OK'
32 | Temp 19 | Temperature | 28.00 | C | 'OK'
33 | Temp 20 | Temperature | 27.00 | C | 'OK'
34 | Temp 21 | Temperature | 28.00 | C | 'OK'
35 | Temp 22 | Temperature | 32.00 | C | 'OK'
36 | Temp 23 | Temperature | 45.00 | C | 'OK'
37 | Temp 24 | Temperature | 29.00 | C | 'OK'
38 | Temp 25 | Temperature | 37.00 | C | 'OK'
39 | Temp 26 | Temperature | 41.00 | C | 'OK'
40 | Temp 27 | Temperature | 49.00 | C | 'OK'
41 | Temp 28 | Temperature | 73.00 | C | 'OK'
42 | Temp 29 | Temperature | 67.00 | C | 'OK'
43 | Temp 30 | Temperature | 37.00 | C | 'OK'
44 | Temp 31 | Temperature | 37.00 | C | 'OK'
45 | Temp 32 | Temperature | 32.00 | C | 'OK'
46 | Temp 33 | Temperature | N/A | C | N/A
47 | Temp 34 | Temperature | N/A | C | N/A
48 | Temp 35 | Temperature | N/A | C | N/A
49 | Temp 36 | Temperature | N/A | C | N/A
50 | Memory | Memory | N/A | N/A | 'Presence
detected'
51 | Power Meter | Current | N/A | N/A | 'Device Enabled'
---
I know ilo folks use ipmitool a lot for testing. I'm endeavoring for more
comparison of other ipmi utilities as well (e.g. freeipmi).
I had been meaning to mail about this difference (Fan/Power readings), so
now I'll see if we can work out that issue. :)
On Mon, Mar 14, 2011 at 10:41 AM, Albert Chu <address@hidden> wrote:
> Hi Nicola,
>
> I'll ping someone at HP I know that might be a bit more "in the know".
> I'm sure the support person you talked to just has no idea what they're
> talking about :P
>
> Al
>
> On Sun, 2011-03-13 at 10:21 -0700, Nicola Pedrozzi wrote:
> > Hello Albert,
> > ping-ing HP didn't help, since I'm on Slackware, they just don't care.
> >
> > They said IPMI is based on SNMP and all the info should be there already.
> >
> > :^) they also said that you could just download their HPSIM package for
> Suse
> > or Redhat and have a look in there , ???? , I said: into the
> binaries????????
> >
> > Ok, just give up. I'll try to live with that ...... ;^( , usually
> temperatures
> > should be enough.
> >
> > FYI:
> > . I flashed the BIOS firmware to the latest available
> > . I tried recompiling the kernel with a default huge .configuration file
> > from Slackware (that is, compiling many things that I'm not supposed
> to need)
> > . I tried ipmitool-1.8.11
> > . I tried lm_sensors-3.2.0
> >
> > Not much changed ... just once, ipmitool seemed to work but, at a second
> run,
> > it started again complaining about "Unable to open SDR for reading".
> > I actually could not read all of the output because I used to many
> -vvvvvvvvvvv ...
> > and my terminal scrolling (1500 lines) was not enough.
> > I tried load/remove/reload/... many modules but I could not reproduce it.
> >
> >
> >
> > Thank you anyway and keep up with your great job,
> > Bye nIc
> >
> >
> >
> > Albert Chu wrote:
> > > Great, it'll be fixed in FreeIPMI 1.0.3.
> > >
> > > Al
> > >
> > > On Fri, 2011-03-11 at 00:50 -0800, Nicola Pedrozzi wrote:
> > >> Hi Al,
> > >> thanks, bmc-info now works:
> > >>
> > >>
> > >> # bmc-info
> > >> Device ID : 19
> > >> Device Revision : 1
> > >> Device SDRs : supported
> > >> Firmware Revision : 1.07
> > >> Device Available : yes (normal operation)
> > >> IPMI Version : 2.0
> > >> Sensor Device : supported
> > >> SDR Repository Device : supported
> > >> SEL Device : supported
> > >> FRU Inventory Device : supported
> > >> IPMB Event Receiver : unsupported
> > >> IPMB Event Generator : unsupported
> > >> Bridge : unsupported
> > >> Chassis Device : unsupported
> > >> Manufacturer ID : Hewlett-Packard (11)
> > >> Product ID : 8224
> > >>
> > >> Channel Information
> > >>
> > >> Channel Number : 2
> > >> Medium Type : 802.3 LAN
> > >> Protocol Type : IPMB-1.0
> > >> Active Session Count : 0
> > >> Session Support : multi-session
> > >> Vendor ID : Intelligent Platform Management Interface forum
> (7154)
> > >>
> > >> Channel Number : 7
> > >> Medium Type : OEM
> > >> Protocol Type : KCS
> > >> Active Session Count : 0
> > >> Session Support : session-less
> > >> Vendor ID : Intelligent Platform Management Interface forum
> (7154)
> > >>
> > >>
> > >>
> > >> About OEM Sensors Id 0 and 1, I'll contact HP to see if they can
> provide some info.
> > >> And maybe some more general specs on their IPMI implementation.
> > >>
> > >>
> > >>
> > >>
> > >> Thanks for now,
> > >> Bye nIc
> > >>
> > >>
> > >>
> > >> Albert Chu wrote:
> > >>> Hi Nicola,
> > >>>
> > >>> I just uploaded a beta of FreeIPMI 1.0.3 here:
> > >>>
> > >>>
> http://download.gluster.com/pub/freeipmi/qa-release/freeipmi-1.0.3.beta0.tar.gz
> > >>>
> > >>> Could you give it a try to see if it runs bmc-info correctly?
> > >>>
> > >>> Thanks,
> > >>> Al
> > >>>
> > >>> On Thu, 2011-03-10 at 15:05 -0800, Albert Chu wrote:
> > >>>> Hi Nicola,
> > >>>>
> > >>>>> =====================================================
> > >>>>> Get System Info Parameters Response
> > >>>>> =====================================================
> > >>>>> KCS Header:
> > >>>>> ------------
> > >>>>> [ 0h] = lun[ 2b]
> > >>>>> [ 7h] = net_fn[ 6b]
> > >>>>> IPMI Command Data:
> > >>>>> ------------------
> > >>>>> [ 59h] = cmd[ 8b]
> > >>>>> [ 80h] = comp_code[ 8b]
> > >>>>>
> ipmi_cmd_get_system_info_parameters_system_firmware_version_first_set: bad
> completion code
> > >>>>
> > >>>> I never handled this particular error code, so I can put in a fix to
> > >>>> deal with this. I'll e-mail you a link to a beta tar.gz later on
> with
> > >>>> the fix.
> > >>>>
> > >>>> Looking at the ipmi-sensors debug data, it seems legitimate.
> There's
> > >>>> nothing to indicate that there should be more sensors. The sensors
> that
> > >>>> report N/A are not available. If it's a bug on HP's part, that's on
> > >>>> their firmware side and you'd have to ping them on that.
> > >>>>
> > >>>> One additional note:
> > >>>>
> > >>>> 0 | System Chassis 1 UID Light | OEM Reserved | N/A
> > >>>> | N/A | 'OEM Event = 0000h'
> > >>>> 1 | System Chassis 2 Sys. Health LED | OEM Reserved | N/A
> | N/A | 'OEM Event = 0000h'
> > >>>>
> > >>>> It'd be nice to support these OEM sensors. If you can ping HP and
> > >>>> determine how to interpret these two sensors, I can add OEM
> > >>>> interpretations into FreeIPMI for them.
> > >>>>
> > >>>> Al
> > >>>>
> > >>>> On Thu, 2011-03-10 at 14:11 -0800, Nicola Pedrozzi wrote:
> > >>>>> Hi Albert,
> > >>>>> first of all thanks for your prompt reply.
> > >>>>>
> > >>>>> The --entity-sensor-names helped a bit, but still some infos are
> missing, more specifically the RPM
> > >>>>> of the fans (there is space for 6 fans and correctly only the first
> 4 are showed because in my
> > >>>>> system config I only have 4, but I think somewhere there should
> also be the fans RPM of the 2 Power
> > >>>>> Supply...).
> > >>>>>
> > >>>>>
> > >>>>> Here the output with your suggested option:
> > >>>>>
> > >>>>> # ipmi-sensors --entity-sensor-names
> > >>>>> ID | Name | Type |
> Reading | Units | Event
> > >>>>> 0 | System Chassis 1 UID Light | OEM Reserved | N/A
> | N/A | 'OEM Event = 0000h'
> > >>>>> 1 | System Chassis 2 Sys. Health LED | OEM Reserved | N/A
> | N/A | 'OEM Event = 0000h'
> > >>>>> 2 | Power Supply 1 Power Supply 1 | Power Supply | N/A
> | N/A | 'Presence detected'
> > >>>>> 3 | Power Supply 2 Power Supply 2 | Power Supply | N/A
> | N/A | 'Presence detected'
> > >>>>> 4 | Power Supply 3 Power Supplies | Power Supply | N/A
> | N/A | 'Fully Redundant'
> > >>>>> 6 | System Board 1 Fan 1 | Fan | N/A
> | N/A | 'transition to
> > >>>>> Running'
> > >>>>> 7 | System Board 2 Fan 2 | Fan | N/A
> | N/A | 'transition to
> > >>>>> Running'
> > >>>>> 8 | System Board 3 Fan 3 | Fan | N/A
> | N/A | 'transition to
> > >>>>> Running'
> > >>>>> 9 | System Board 4 Fan 4 | Fan | N/A
> | N/A | 'transition to
> > >>>>> Running'
> > >>>>> 10 | System Board 5 Fan 5 | Fan | N/A
> | N/A | N/A
> > >>>>> 11 | System Board 6 Fan 6 | Fan | N/A
> | N/A | N/A
> > >>>>> 12 | System Board 7 Fans | Fan | N/A
> | N/A | 'Fully Redundant'
> > >>>>> 14 | Air Inlet Temp 1 | Temperature |
> 20.00 | C | 'OK'
> > >>>>> 15 | Processor 1 Temp 2 | Temperature |
> 40.00 | C | 'OK'
> > >>>>> 16 | Processor 2 Temp 3 | Temperature | N/A
> | C | N/A
> > >>>>> 17 | Memory Module 1 Temp 4 | Temperature |
> 37.00 | C | 'OK'
> > >>>>> 18 | Memory Module 2 Temp 5 | Temperature |
> 37.00 | C | 'OK'
> > >>>>> 19 | Memory Module 3 Temp 6 | Temperature | N/A
> | C | N/A
> > >>>>> 20 | Memory Module 4 Temp 7 | Temperature | N/A
> | C | N/A
> > >>>>> 21 | Power Unit 1 Temp 8 | Temperature |
> 45.00 | C | 'OK'
> > >>>>> 22 | Power Unit 2 Temp 9 | Temperature |
> 37.00 | C | 'OK'
> > >>>>> 23 | System Board 1 Temp 10 | Temperature |
> 47.00 | C | 'OK'
> > >>>>> 24 | System Board 2 Temp 11 | Temperature |
> 38.00 | C | 'OK'
> > >>>>> 25 | System Board 3 Temp 12 | Temperature |
> 49.00 | C | 'OK'
> > >>>>> 26 | System Internal Expansion Board 1 Temp 13 | Temperature | N/A
> | C | N/A
> > >>>>> 27 | System Internal Expansion Board 2 Temp 14 | Temperature | N/A
> | C | N/A
> > >>>>> 28 | System Internal Expansion Board 3 Temp 15 | Temperature | N/A
> | C | N/A
> > >>>>> 29 | System Internal Expansion Board 4 Temp 16 | Temperature | N/A
> | C | N/A
> > >>>>> 30 | System Internal Expansion Board 5 Temp 17 | Temperature | N/A
> | C | N/A
> > >>>>> 31 | System Internal Expansion Board 6 Temp 18 | Temperature | N/A
> | C | N/A
> > >>>>> 32 | System Board 4 Temp 19 | Temperature |
> 27.00 | C | 'OK'
> > >>>>> 33 | System Board 5 Temp 20 | Temperature |
> 33.00 | C | 'OK'
> > >>>>> 34 | System Board 6 Temp 21 | Temperature |
> 36.00 | C | 'OK'
> > >>>>> 35 | System Board 7 Temp 22 | Temperature |
> 33.00 | C | 'OK'
> > >>>>> 36 | System Board 8 Temp 23 | Temperature |
> 44.00 | C | 'OK'
> > >>>>> 37 | System Board 9 Temp 24 | Temperature |
> 37.00 | C | 'OK'
> > >>>>> 38 | System Board 10 Temp 25 | Temperature |
> 33.00 | C | 'OK'
> > >>>>> 39 | System Board 11 Temp 26 | Temperature |
> 33.00 | C | 'OK'
> > >>>>> 40 | System Internal Expansion Board 7 Temp 27 | Temperature | N/A
> | C | N/A
> > >>>>> 41 | System Internal Expansion Board 8 Temp 28 | Temperature | N/A
> | C | N/A
> > >>>>> 42 | Drive Backplane Temp 29 | Temperature |
> 35.00 | C | 'OK'
> > >>>>> 43 | System Board 12 Temp 30 | Temperature |
> 77.00 | C | 'OK'
> > >>>>> 44 | System Board 8 Memory | Memory | N/A
> | N/A | 'Presence detected'
> > >>>>> 45 | System Board 9 Power Meter | Current | N/A
> | N/A | 'Device Enabled'
> > >>>>>
> > >>>>>
> > >>>>>
> > >>>>>
> > >>>>> Here the bmc-info --debug output (the one of ipmi-sensor is
> attached as .gz):
> > >>>>>
> > >>>>>
> > >>>>> # bmc-info --debug
> > >>>>> =====================================================
> > >>>>> Get Device ID Request
> > >>>>> =====================================================
> > >>>>> KCS Header:
> > >>>>> ------------
> > >>>>> [ 0h] = lun[ 2b]
> > >>>>> [ 6h] = net_fn[ 6b]
> > >>>>> IPMI Command Data:
> > >>>>> ------------------
> > >>>>> [ 1h] = cmd[ 8b]
> > >>>>> =====================================================
> > >>>>> Get Device ID Response
> > >>>>> =====================================================
> > >>>>> KCS Header:
> > >>>>> ------------
> > >>>>> [ 0h] = lun[ 2b]
> > >>>>> [ 7h] = net_fn[ 6b]
> > >>>>> IPMI Command Data:
> > >>>>> ------------------
> > >>>>> [ 1h] = cmd[ 8b]
> > >>>>> [ 0h] = comp_code[ 8b]
> > >>>>> [ 13h] = device_id[ 8b]
> > >>>>> [ 1h] = device_revision.revision[ 4b]
> > >>>>> [ 0h] = device_revision.reserved1[ 3b]
> > >>>>> [ 1h] = device_revision.sdr_support[ 1b]
> > >>>>> [ 1h] = firmware_revision1.major_revision[ 7b]
> > >>>>> [ 0h] = firmware_revision1.device_available[ 1b]
> > >>>>> [ 7h] = firmware_revision2.minor_revision[ 8b]
> > >>>>> [ 2h] = ipmi_version_major[ 4b]
> > >>>>> [ 0h] = ipmi_version_minor[ 4b]
> > >>>>> [ 1h] = additional_device_support.sensor_device[ 1b]
> > >>>>> [ 1h] =
> additional_device_support.sdr_repository_device[ 1b]
> > >>>>> [ 1h] = additional_device_support.sel_device[ 1b]
> > >>>>> [ 1h] =
> additional_device_support.fru_inventory_device[ 1b]
> > >>>>> [ 0h] =
> additional_device_support.ipmb_event_receiver[ 1b]
> > >>>>> [ 0h] =
> additional_device_support.ipmb_event_generator[ 1b]
> > >>>>> [ 0h] = additional_device_support.bridge[ 1b]
> > >>>>> [ 0h] = additional_device_support.chassis_device[ 1b]
> > >>>>> [ Bh] = manufacturer_id.id[20b]
> > >>>>> [ 0h] = manufacturer_id.reserved1[ 4b]
> > >>>>> [ 2020h] = product_id[16b]
> > >>>>> Device ID : 19
> > >>>>> Device Revision : 1
> > >>>>> Device SDRs : supported
> > >>>>> Firmware Revision : 1.07
> > >>>>> Device Available : yes (normal operation)
> > >>>>> IPMI Version : 2.0
> > >>>>> Sensor Device : supported
> > >>>>> SDR Repository Device : supported
> > >>>>> SEL Device : supported
> > >>>>> FRU Inventory Device : supported
> > >>>>> IPMB Event Receiver : unsupported
> > >>>>> IPMB Event Generator : unsupported
> > >>>>> Bridge : unsupported
> > >>>>> Chassis Device : unsupported
> > >>>>> Manufacturer ID : Hewlett-Packard (11)
> > >>>>> Product ID : 8224
> > >>>>>
> > >>>>> =====================================================
> > >>>>> Get Device GUID Request
> > >>>>> =====================================================
> > >>>>> KCS Header:
> > >>>>> ------------
> > >>>>> [ 0h] = lun[ 2b]
> > >>>>> [ 6h] = net_fn[ 6b]
> > >>>>> IPMI Command Data:
> > >>>>> ------------------
> > >>>>> [ 8h] = cmd[ 8b]
> > >>>>> =====================================================
> > >>>>> Get Device GUID Response
> > >>>>> =====================================================
> > >>>>> KCS Header:
> > >>>>> ------------
> > >>>>> [ 0h] = lun[ 2b]
> > >>>>> [ 7h] = net_fn[ 6b]
> > >>>>> IPMI Command Data:
> > >>>>> ------------------
> > >>>>> [ 8h] = cmd[ 8b]
> > >>>>> [ C1h] = comp_code[ 8b]
> > >>>>> =====================================================
> > >>>>> Get System Info Parameters Request
> > >>>>> =====================================================
> > >>>>> KCS Header:
> > >>>>> ------------
> > >>>>> [ 0h] = lun[ 2b]
> > >>>>> [ 6h] = net_fn[ 6b]
> > >>>>> IPMI Command Data:
> > >>>>> ------------------
> > >>>>> [ 59h] = cmd[ 8b]
> > >>>>> [ 0h] = reserved[ 7b]
> > >>>>> [ 0h] = get_parameter[ 1b]
> > >>>>> [ 1h] = parameter_selector[ 8b]
> > >>>>> [ 0h] = set_selector[ 8b]
> > >>>>> [ 0h] = block_selector[ 8b]
> > >>>>> =====================================================
> > >>>>> Get System Info Parameters Response
> > >>>>> =====================================================
> > >>>>> KCS Header:
> > >>>>> ------------
> > >>>>> [ 0h] = lun[ 2b]
> > >>>>> [ 7h] = net_fn[ 6b]
> > >>>>> IPMI Command Data:
> > >>>>> ------------------
> > >>>>> [ 59h] = cmd[ 8b]
> > >>>>> [ 80h] = comp_code[ 8b]
> > >>>>>
> ipmi_cmd_get_system_info_parameters_system_firmware_version_first_set: bad
> completion code
> > >>>>>
> > >>>>>
> > >>>>>
> > >>>>>
> > >>>>> Thank you and good night,
> > >>>>> nIc
> > >>>>>
> > >>>>>
> > >>>>>
> > >>>>> Albert Chu wrote:
> > >>>>>> Hi Nicola,
> > >>>>>>
> > >>>>>> If you could you provide --debug output, that'd be great. For
> bmc-info,
> > >>>>>> I'm betting the HP node returns some non-standard error code, so I
> don't
> > >>>>>> handle that error code correctly (I would normally expect the "Not
> > >>>>>> supported" or "Invalid" error code if it isn't supported).
> > >>>>>>
> > >>>>>> As for the ipmi-sensors output, it appears pretty solid. If you
> are
> > >>>>>> comparing the names to HP specific software, it's possible that
> there is
> > >>>>>> extra info (via OEM extensions) that the HP specific software
> knows of
> > >>>>>> that I don't. Or you may want to try the --entity-sensor-names
> option
> > >>>>>> in ipmi-sensors. I noticed on Dell motherboards that they "name"
> their
> > >>>>>> sensors by combining an entity ID with a text string. It's
> possible HP
> > >>>>>> software does something similar. If --entity-sensor-names doesn't
> work,
> > >>>>>> we'd have to come up with a new option.
> > >>>>>>
> > >>>>>> As for the not listing specific sensors, it's hard to say. Some
> > >>>>>> motherboards don't support the sensors you're interested in. It's
> also
> > >>>>>> possible the "N/A" outputs are due to a bug in HP's firmware. If
> you
> > >>>>>> send me the --debug output, I might be able to see if there is
> anything
> > >>>>>> particularly odd about it.
> > >>>>>>
> > >>>>>> Al
> > >>>>>>
> > >>>>>> On Thu, 2011-03-10 at 09:25 -0800, Nicola Pedrozzi wrote:
> > >>>>>>> Hello everybody,
> > >>>>>>> today I installed freeipmi-1.0.2 on the following system:
> > >>>>>>>
> > >>>>>>> . HP Proliant DL380 G7
> > >>>>>>> . Slackware 13.1
> > >>>>>>> . OS 2.6.35.11 x86_64 (compiled by myself)
> > >>>>>>> . 1x Xeon(R) CPU E5630 @ 2.53GHz
> > >>>>>>> . 2x redundant Power Supply (detected)
> > >>>>>>> . 4x redundant Fan (detected)
> > >>>>>>>
> > >>>>>>>
> > >>>>>>> Things seem to work but not completely. I cannot manage to output
> some
> > >>>>>>> important information such as Fan/RPM and the "Name" of the
> showed
> > >>>>>>> temperatures.
> > >>>>>>>
> > >>>>>>> bcm-info gives an error and does not fully complete:
> > >>>>>>>
> > >>>>>>> # bmc-info
> > >>>>>>> Device ID : 19
> > >>>>>>> Device Revision : 1
> > >>>>>>> Device SDRs : supported
> > >>>>>>> Firmware Revision : 1.07
> > >>>>>>> Device Available : yes (normal operation)
> > >>>>>>> IPMI Version : 2.0
> > >>>>>>> Sensor Device : supported
> > >>>>>>> SDR Repository Device : supported
> > >>>>>>> SEL Device : supported
> > >>>>>>> FRU Inventory Device : supported
> > >>>>>>> IPMB Event Receiver : unsupported
> > >>>>>>> IPMB Event Generator : unsupported
> > >>>>>>> Bridge : unsupported
> > >>>>>>> Chassis Device : unsupported
> > >>>>>>> Manufacturer ID : Hewlett-Packard (11)
> > >>>>>>> Product ID : 8224
> > >>>>>>>
> > >>>>>>>
> ipmi_cmd_get_system_info_parameters_system_firmware_version_first_set:
> > >>>>>>> bad completion code
> > >>>>>>>
> > >>>>>>>
> > >>>>>>>
> > >>>>>>>
> > >>>>>>> And here the output of ipmi-sensors
> > >>>>>>>
> > >>>>>>> # ipmi-sensors --interpret-oem-data
> > >>>>>>>
> > >>>>>>> ID | Name | Type | Reading | Units | Event
> > >>>>>>> 0 | UID Light | OEM Reserved | N/A | N/A | 'OEM
> Event =
> > >>>>>>> 0000h'
> > >>>>>>> 1 | Sys. Health LED | OEM Reserved | N/A | N/A | 'OEM
> Event =
> > >>>>>>> 0000h'
> > >>>>>>> 2 | Power Supply 1 | Power Supply | N/A | N/A |
> 'Presence
> > >>>>>>> detected'
> > >>>>>>> 3 | Power Supply 2 | Power Supply | N/A | N/A |
> 'Presence
> > >>>>>>> detected'
> > >>>>>>> 4 | Power Supplies | Power Supply | N/A | N/A | 'Fully
> Redundant'
> > >>>>>>> 6 | Fan 1 | Fan | N/A | N/A |
> 'transition
> > >>>>>>> to Running'
> > >>>>>>> 7 | Fan 2 | Fan | N/A | N/A |
> 'transition
> > >>>>>>> to Running'
> > >>>>>>> 8 | Fan 3 | Fan | N/A | N/A |
> 'transition
> > >>>>>>> to Running'
> > >>>>>>> 9 | Fan 4 | Fan | N/A | N/A |
> 'transition
> > >>>>>>> to Running'
> > >>>>>>> 10 | Fan 5 | Fan | N/A | N/A | N/A
> > >>>>>>> 11 | Fan 6 | Fan | N/A | N/A | N/A
> > >>>>>>> 12 | Fans | Fan | N/A | N/A | 'Fully
> Redundant'
> > >>>>>>> 14 | Temp 1 | Temperature | 22.00 | C | 'OK'
> > >>>>>>> 15 | Temp 2 | Temperature | 40.00 | C | 'OK'
> > >>>>>>> 16 | Temp 3 | Temperature | N/A | C | N/A
> > >>>>>>> 17 | Temp 4 | Temperature | 38.00 | C | 'OK'
> > >>>>>>> 18 | Temp 5 | Temperature | 39.00 | C | 'OK'
> > >>>>>>> 19 | Temp 6 | Temperature | N/A | C | N/A
> > >>>>>>> 20 | Temp 7 | Temperature | N/A | C | N/A
> > >>>>>>> 21 | Temp 8 | Temperature | 46.00 | C | 'OK'
> > >>>>>>> 22 | Temp 9 | Temperature | 38.00 | C | 'OK'
> > >>>>>>> 23 | Temp 10 | Temperature | 48.00 | C | 'OK'
> > >>>>>>> 24 | Temp 11 | Temperature | 39.00 | C | 'OK'
> > >>>>>>> 25 | Temp 12 | Temperature | 50.00 | C | 'OK'
> > >>>>>>> 26 | Temp 13 | Temperature | N/A | C | N/A
> > >>>>>>> 27 | Temp 14 | Temperature | N/A | C | N/A
> > >>>>>>> 28 | Temp 15 | Temperature | N/A | C | N/A
> > >>>>>>> 29 | Temp 16 | Temperature | N/A | C | N/A
> > >>>>>>> 30 | Temp 17 | Temperature | N/A | C | N/A
> > >>>>>>> 31 | Temp 18 | Temperature | N/A | C | N/A
> > >>>>>>> 32 | Temp 19 | Temperature | 28.00 | C | 'OK'
> > >>>>>>> 33 | Temp 20 | Temperature | 35.00 | C | 'OK'
> > >>>>>>> 34 | Temp 21 | Temperature | 38.00 | C | 'OK'
> > >>>>>>> 35 | Temp 22 | Temperature | 34.00 | C | 'OK'
> > >>>>>>> 36 | Temp 23 | Temperature | 44.00 | C | 'OK'
> > >>>>>>> 37 | Temp 24 | Temperature | 38.00 | C | 'OK'
> > >>>>>>> 38 | Temp 25 | Temperature | 34.00 | C | 'OK'
> > >>>>>>> 39 | Temp 26 | Temperature | 34.00 | C | 'OK'
> > >>>>>>> 40 | Temp 27 | Temperature | N/A | C | N/A
> > >>>>>>> 41 | Temp 28 | Temperature | N/A | C | N/A
> > >>>>>>> 42 | Temp 29 | Temperature | 35.00 | C | 'OK'
> > >>>>>>> 43 | Temp 30 | Temperature | 77.00 | C | 'OK'
> > >>>>>>> 44 | Memory | Memory | N/A | N/A |
> 'Presence
> > >>>>>>> detected'
> > >>>>>>> 45 | Power Meter | Current | N/A | N/A |
> 'Device Enabled'
> > >>>>>>>
> > >>>>>>>
> > >>>>>>>
> > >>>>>>> If useful, I'll provide --debug output.
> > >>>>>>>
> > >>>>>>>
> > >>>>>>>
> > >>>>>>> Thanks for any help,
> > >>>>>>> bye nIc
> > >>>>>>>
> > >>>>>>> _______________________________________________
> > >>>>>>> Freeipmi-users mailing list
> > >>>>>>> address@hidden
> > >>>>>>> http://lists.gnu.org/mailman/listinfo/freeipmi-users
> > >>>>>
> > >>>>>
> > >>>>> --
> > >>>>>
> > >>>>>
> > >>>>> Cordiali saluti,
> > >>>>> Nicola Pedrozzi
> > >>>>> --
> > >>>>> IT Manager
> > >>>>> ImmoGalaxy Sagl
> > >>>>> Via Corte 19c
> > >>>>> CH-6963 Pregassona
> > >>>>>
> > >>>>> address@hidden
> > >>>>> Tel: +41 91 941.08.01
> > >>>>> Fax: +41 91 941.08.02
> > >>>>>
> > >>>>> http://www.immogalaxy.ch
> > >>>> --
> > >>>> Albert Chu
> > >>>> address@hidden
> > >>>> Computer Scientist
> > >>>> High Performance Systems Division
> > >>>> Lawrence Livermore National Laboratory
> > >>>>
> > >>>>
> > >>>> _______________________________________________
> > >>>> Freeipmi-users mailing list
> > >>>> address@hidden
> > >>>> http://lists.gnu.org/mailman/listinfo/freeipmi-users
> > >>
> --
> Albert Chu
> address@hidden
> Computer Scientist
> High Performance Systems Division
> Lawrence Livermore National Laboratory
>
>
> _______________________________________________
> Freeipmi-users mailing list
> address@hidden
> http://lists.gnu.org/mailman/listinfo/freeipmi-users
>
- [Freeipmi-users] Missing details on HP Proliant DL380 G7, Nicola Pedrozzi, 2011/03/10
- Re: [Freeipmi-users] Missing details on HP Proliant DL380 G7, Albert Chu, 2011/03/10
- Re: [Freeipmi-users] Missing details on HP Proliant DL380 G7, Nicola Pedrozzi, 2011/03/10
- Re: [Freeipmi-users] Missing details on HP Proliant DL380 G7, Albert Chu, 2011/03/10
- Re: [Freeipmi-users] Missing details on HP Proliant DL380 G7, Albert Chu, 2011/03/10
- Re: [Freeipmi-users] Missing details on HP Proliant DL380 G7, Nicola Pedrozzi, 2011/03/11
- Re: [Freeipmi-users] Missing details on HP Proliant DL380 G7, Albert Chu, 2011/03/11
- Re: [Freeipmi-users] Missing details on HP Proliant DL380 G7, Nicola Pedrozzi, 2011/03/13
- Re: [Freeipmi-users] Missing details on HP Proliant DL380 G7, Albert Chu, 2011/03/14
- Re: [Freeipmi-users] Missing details on HP Proliant DL380 G7,
Christopher Maestas <=
- Re: [Freeipmi-users] Missing details on HP Proliant DL380 G7, Albert Chu, 2011/03/22
- Re: [Freeipmi-users] Missing details on HP Proliant DL380 G7, Albert Chu, 2011/03/24
- Re: [Freeipmi-users] Missing details on HP Proliant DL380 G7, Christopher Maestas, 2011/03/28