[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Freeipmi-users] HP ProLiant ML310 G5 does not support fan reading?
From: |
Albert Chu |
Subject: |
Re: [Freeipmi-users] HP ProLiant ML310 G5 does not support fan reading? |
Date: |
Wed, 04 May 2011 15:26:33 -0700 |
Hi Franta,
Great. I don't believe the first two have readings, that's just the way
they are. The HP fellow I know said he will try to figure out to
interpret the OEM event of the first sensor. Until I get that info, all
I can output is "0000h".
Thanks,
Al
On Wed, 2011-05-04 at 14:16 -0700, Frantisek Hanzlik wrote:
> Hello Al,
>
> You are right and Your fix is working, below is ipmi-sensors w/o and
> with "-W discretereading" option. First two ID's (Health LED and VRM)
> are still not displayed, but I not need them. Fan speeds in percentage
> of maximum doesn't matter, it's OK.
> Even lower is first part of dmidecode output, for better machine model
> identification.
>
> Many thanks for Your work! I see that project vitality has very high
> score, I wish You many further successes!
>
> Franta
>
> address@hidden log]# ipmi-sensors
> ID | Name | Type | Reading | Units | Event
> 1 | Int. Health LED | OEM Reserved | N/A | N/A | 'OEM Event = 0000h'
> 2 | VRM (CPU1) | Power Unit | N/A | N/A | 'Device
> Inserted/Device Present'
> 3 | CPU Fan | Fan | N/A | N/A | 'transition to
> Running'
> 4 | Rear Fan | Fan | N/A | N/A | 'transition to
> Running'
> 5 | Temp 1 | Temperature | 32.00 | C | 'OK'
> 6 | Temp 2 | Temperature | 30.00 | C | 'OK'
> 7 | Temp 3 | Temperature | 22.00 | C | 'OK'
>
> address@hidden log]# ipmi-sensors -W "discretereading"
> ID | Name | Type | Reading | Units | Event
> 1 | Int. Health LED | OEM Reserved | N/A | N/A | 'OEM Event = 0000h'
> 2 | VRM (CPU1) | Power Unit | N/A | N/A | 'Device
> Inserted/Device Present'
> 3 | CPU Fan | Fan | 60.37 | % | 'transition to
> Running'
> 4 | Rear Fan | Fan | 33.32 | % | 'transition to
> Running'
> 5 | Temp 1 | Temperature | 32.00 | C | 'OK'
> 6 | Temp 2 | Temperature | 30.00 | C | 'OK'
> 7 | Temp 3 | Temperature | 22.00 | C | 'OK'
>
>
> #------------------------------------------------------------------------
> # dmidecode 2.11
> SMBIOS 2.4 present.
> 56 structures occupying 1594 bytes.
> Table at 0x000EE000.
>
> Handle 0x0000, DMI type 0, 24 bytes
> BIOS Information
> Vendor: HP
> Version: W05
> Release Date: 11/15/2007
> Address: 0xF0000
> Runtime Size: 64 kB
> ROM Size: 4096 kB
> Characteristics:
> PCI is supported
> PNP is supported
> BIOS is upgradeable
> BIOS shadowing is allowed
> ESCD support is available
> Boot from CD is supported
> Selectable boot is supported
> EDD is supported
> 5.25"/360 kB floppy services are supported (int 13h)
> 5.25"/1.2 MB floppy services are supported (int 13h)
> 3.5"/720 kB floppy services are supported (int 13h)
> Print screen service is supported (int 5h)
> 8042 keyboard services are supported (int 9h)
> Serial services are supported (int 14h)
> Printer services are supported (int 17h)
> CGA/mono video services are supported (int 10h)
> ACPI is supported
> USB legacy is supported
> BIOS boot specification is supported
> Function key-initiated network boot is supported
> Targeted content distribution is supported
>
> Handle 0x0100, DMI type 1, 27 bytes
> System Information
> Manufacturer: HP
> Product Name: ProLiant ML310 G5
> Version: Not Specified
> Serial Number: CZ1751005W
> UUID: 34343533-3336-435A-3137-353130303557
> Wake-up Type: Power Switch
> SKU Number: 445336-421
> Family: ProLiant
>
> Handle 0x0300, DMI type 3, 19 bytes
> Chassis Information
> Manufacturer: HP
> Type: Tower
> Lock: Not Present
> Version: Not Specified
> Serial Number: CZ1751005W
> Asset Tag:
> Boot-up State: Unknown
> Power Supply State: Unknown
> Thermal State: Unknown
> Security Status: Unknown
> OEM Information: 0x00000000
> Height: Unspecified
> Number Of Power Cords: 1
> ....
>
>
> Albert Chu wrote:
> > Hi Frantisek,
> >
> > Good timing, there should be a fix for you in 1.0.4 assuming it is the
> > same issue that was seen on another HP motherboard. The workaround can
> > be executed using the
> >
> > -W "discretereading"
> >
> > on the command line, or setting the flag permantently in freeipmi.conf.
> > If it works for you, PLMK so I can your motherboard to FreeIPMI's
> > documentation. (As a side note, on some HP motherboards, they tend to
> > output percentage of fan max RPM, rather than the actual RPM.)
> >
> > The short story on the issue, the SDR records on the HP motherboard are
> > messed up and list "conflicting" information. Whether intentional or a
> > mistake, I don't know (perhaps they were trying to be clever and
> > compacting information in a way they shouldn't have?).
> >
> > There's an HP fellow on this mailing list that is trying to get it
> > sorted out in their firmware.
> >
> > Al
> >
> > On Tue, 2011-05-03 at 18:15 -0700, Frantisek Hanzlik wrote:
> >> I just tried freeipmi (0.8.8 and 1.0.4) on this small server.
> >> "ipmi-sensors" give output:
> >>
> >> ID | Name | Type | Reading | Units | Event
> >> 1 | Int. Health LED | OEM Reserved | N/A | N/A | 'OEM Event =
> >> 0000h'
> >> 2 | VRM (CPU1) | Power Unit | N/A | N/A | 'Device
> >> Inserted/Device Present'
> >> 3 | CPU Fan | Fan | N/A | N/A | 'transition to
> >> Running'
> >> 4 | Rear Fan | Fan | N/A | N/A | 'transition to
> >> Running'
> >> 5 | Temp 1 | Temperature | 32.00 | C | 'OK'
> >> 6 | Temp 2 | Temperature | 30.00 | C | 'OK'
> >> 7 | Temp 3 | Temperature | 22.00 | C | 'OK'
> >>
> >> I'm surprised, as there are no fan rotation speed values, nor some
> >> other values, as if they were not available - "N/A" in "Reading"
> >> column. Although it is entry-level server, sensors for these values
> >> now have even cheapest desktops, I'm right?
> >>
> >> Is possible that server cannot measure these values, or may be
> >> there another problem?
> >>
> >> "bmc-info" display:
> >>
> >> Device ID : 17
> >> Device Revision : 1
> >> Device SDRs : supported
> >> Firmware Revision : 1.42
> >> Device Available : yes (normal operation)
> >> IPMI Version : 2.0
> >> Sensor Device : supported
> >> SDR Repository Device : supported
> >> SEL Device : supported
> >> FRU Inventory Device : supported
> >> IPMB Event Receiver : unsupported
> >> IPMB Event Generator : unsupported
> >> Bridge : unsupported
> >> Chassis Device : unsupported
> >> Manufacturer ID : Hewlett-Packard (11)
> >> Product ID : 0
> >>
> >> Channel Information
> >>
> >> Channel Number : 7
> >> Medium Type : OEM
> >> Protocol Type : KCS
> >> Active Session Count : 0
> >> Session Support : session-less
> >> Vendor ID : Intelligent Platform Management Interface forum
> >> (7154)
> >>
> >>
> >> Thank in advance, Franta Hanzlík
--
Albert Chu
address@hidden
Computer Scientist
High Performance Systems Division
Lawrence Livermore National Laboratory