[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Freeipmi-users] Send Message using FreeIPMI
From: |
Phil_Chidester |
Subject: |
Re: [Freeipmi-users] Send Message using FreeIPMI |
Date: |
Mon, 12 Sep 2011 15:48:22 -0500 |
Hi Al,
Thanks for the quick response. I am using a similar command to yours however I
am getting :
Unable to send command: Invalid argument
What I am doing is having two BMCs talk to each other over IPMB. Currently both
addresses are 0x20 however.
I tried this command as well for bridging sdrs :
ipmitool -m 0x20 -t 0x20 sdr
However it just returned the host sdr not the peer sdr.
Do I need to change the address of the peer controller to something besides
0x20 and provide a SRC Type 12 (Management Controller Device Locator Record)?
Thanks in advance,
Phil Chidester
Storage Engineering
Dell | PG Development
512 728-4840
-----Original Message-----
From: Albert Chu [mailto:address@hidden
Sent: Monday, September 12, 2011 12:48 PM
To: Chidester, Phil
Cc: address@hidden
Subject: Re: [Freeipmi-users] Send Message using FreeIPMI
Hi Phil,
Are you trying to program a raw command via libfreeipmi? What problems are you
having?
It's sort of hard to describe a raw command to do it, since one normally uses
it to encapsulate another command for bridging, and its dependent on the
channel and addresses you're sending to. Here's an example of a send message,
bridging a sensor read, on a motheboard I have.
ipmi-raw 0 6 0x34 0x06 0x2c 0x10 0xc4 0x20 0x4e 0x2d 0x1a 0x4b
Here's the packet I created it from.
=====================================================
Send Message Request
=====================================================
KCS Header:
------------
[ 0h] = lun[ 2b]
[ 6h] = net_fn[ 6b]
IPMI Command Data:
------------------
[ 34h] = cmd[ 8b]
[ 6h] = channel_number[ 4b]
[ 0h] = send_message_with_authentication[ 1b]
[ 0h] = send_message_with_encryption[ 1b]
[ 0h] = tracking_operation[ 2b]
IPMB Message Header:
--------------------
[ 2Ch] = rs_addr[ 8b]
[ 0h] = rs_lun[ 2b]
[ 4h] = net_fn[ 6b]
[ C4h] = checksum1[ 8b]
[ 20h] = rq_addr[ 8b]
[ 2h] = rq_lun[ 2b]
[ 13h] = rq_seq[ 6b]
IPMB Message Data:
------------------
[ 2Dh] = cmd[ 8b]
[ 1Ah] = sensor_number[ 8b]
IPMB Message Trailer:
---------------------
[ 4Bh] = checksum2[ 8b]
Al
On Sun, 2011-09-11 at 13:19 -0700, address@hidden wrote:
> I am trying to do a IPMI Send Message Command using Free IPMI but having
> problems.
> Can someone send the RAW format for the IPMI Send Message Command?
>
>
> Phil Chidester
> Storage Engineering
> Dell | PG Development
> 512 728-4840
>
> _______________________________________________
> Freeipmi-users mailing list
> address@hidden
> https://lists.gnu.org/mailman/listinfo/freeipmi-users
--
Albert Chu
address@hidden
Computer Scientist
High Performance Systems Division
Lawrence Livermore National Laboratory