[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Freeipmi-users] bmc-config - disable channels.
From: |
VJ |
Subject: |
Re: [Freeipmi-users] bmc-config - disable channels. |
Date: |
Mon, 23 Jan 2017 14:32:41 -0800 |
bmc-config -v checkout
.....
Section Serial_Channel
EndSection
#
# Section Serial_Conf Comments
#
# In the Serial_Conf section, typical serial communication configuration is
# setup. Most users will only be interested in IPMI over LAN, therefore this
# section can generally be ignored.
#
Section Serial_Conf
EndSection
Lan_Conf seems fine.
How do i disable channel 0,6 and 7
Thanks.
On Mon, Jan 23, 2017 at 2:29 PM, VJ <address@hidden> wrote:
> Device ID : 36
> Device Revision : 1
> Device SDRs : unsupported
> Firmware Revision : 1.17
> Device Available : yes (normal operation)
> IPMI Version : 2.0
> Sensor Device : supported
> SDR Repository Device : supported
> SEL Device : supported
> FRU Inventory Device : supported
> IPMB Event Receiver : supported
> IPMB Event Generator : supported
> Bridge : unsupported
> Chassis Device : supported
> Manufacturer ID : INVENTEC CORPORATION (6569)
> Product ID : 54
> Auxiliary Firmware Revision Information : 00000000h
>
> GUID : 00000000-0000-0000-0000-000000000000
>
> System Firmware Version : rsion1.0
> System Name : Manager
> Primary Operating System Name : SE Server 1.0
> Operating System Name :
>
> Channel Information
>
> Channel Number : 0
> Medium Type : IPMB (I2C)
> Protocol Type : IPMB-1.0
> Active Session Count : 0
> Session Support : session-less
> Vendor ID : Intelligent Platform Management Interface forum
> (7154)
>
> Channel Number : 1
> Medium Type : 802.3 LAN
> Protocol Type : IPMB-1.0
> Active Session Count : 0
> Session Support : multi-session
> Vendor ID : Intelligent Platform Management Interface forum
> (7154)
>
> Channel Number : 6
> Medium Type : IPMB (I2C)
> Protocol Type : IPMB-1.0
> Active Session Count : 0
> Session Support : session-less
> Vendor ID : Intelligent Platform Management Interface forum
> (7154)
>
> Channel Number : 7
> Medium Type : System Interface (KCS, SMIC, or BT)
> Protocol Type : KCS
> Active Session Count : 0
> Session Support : session-less
> Vendor ID : Intelligent Platform Management Interface forum
> (7154)
>
> On Mon, Jan 23, 2017 at 1:30 PM, Albert Chu <address@hidden> wrote:
>
>> Hi,
>>
>> What are the other channel numbers (could you show via the output of
>> bmc-info)?
>>
>> Also, could you elaborate on your use case scenario?
>>
>> Thanks,
>>
>> Al
>>
>> On Mon, 2017-01-23 at 13:18 -0800, VJ wrote:
>> > I only see
>> > 1) Lan_Channel
>> > 2) Serial_Channel
>> >
>> >
>> > there are 16 channels and they are not displayed even with -v
>> >
>> > On Thu, Jan 19, 2017 at 11:51 AM, Albert Chu <address@hidden> wrote:
>> > Hi,
>> >
>> > Do you wish to disable a very specific channel number, so you
>> > wish to be
>> > able to enable/disable based on the input of a number? At the
>> > moment
>> > that isn't supported. Could you elaborate on your use case
>> > scenario?
>> >
>> > Other channels are configurable in bmc-config if you specify
>> > --verbose
>> > when you checkout. If there are multiple lan channels you can
>> > configure
>> > both, other less common channels like serial are also output
>> > for
>> > configuration.
>> >
>> > Al
>> >
>> > On Thu, 2017-01-19 at 11:37 -0800, VJ wrote:
>> > > Hi
>> > >
>> > > Can I disable a channel using bmc-config configuration ?
>> > > I dont see the sections disabling or enabling other than lan
>> > channel.
>> > > I looked at bmc-config man page and it doesnt mention it.
>> > >
>> > > Thanks.
>> >
>> > > _______________________________________________
>> > > Freeipmi-users mailing list
>> > > address@hidden
>> > > https://lists.gnu.org/mailman/listinfo/freeipmi-users
>> >
>> > --
>> > Albert Chu
>> > address@hidden
>> > Computer Scientist
>> > High Performance Systems Division
>> > Lawrence Livermore National Laboratory
>> >
>> >
>> >
>> >
>> >
>> >
>> > --
>> > ------------------------------------------------------------
>> ---------------------------
>> > ** Believe in : Hardwork Science God**
>> > ============================================
>> >
>>
>> --
>> Albert Chu
>> address@hidden
>> Computer Scientist
>> High Performance Systems Division
>> Lawrence Livermore National Laboratory
>>
>>
>>
>
>
> --
> ------------------------------------------------------------
> ---------------------------
> ** Believe in : Hardwork Science God**
> ============================================
>
--
---------------------------------------------------------------------------------------
** Believe in : Hardwork Science God**
============================================
- [Freeipmi-users] bmc-config - disable channels., VJ, 2017/01/19
- Re: [Freeipmi-users] bmc-config - disable channels., Albert Chu, 2017/01/19
- Re: [Freeipmi-users] bmc-config - disable channels., VJ, 2017/01/23
- Re: [Freeipmi-users] bmc-config - disable channels., Albert Chu, 2017/01/23
- Re: [Freeipmi-users] bmc-config - disable channels., VJ, 2017/01/23
- Re: [Freeipmi-users] bmc-config - disable channels.,
VJ <=
- Re: [Freeipmi-users] bmc-config - disable channels., Albert Chu, 2017/01/23
- Re: [Freeipmi-users] bmc-config - disable channels., VJ, 2017/01/23
- Re: [Freeipmi-users] bmc-config - disable channels., VJ, 2017/01/23
- Re: [Freeipmi-users] bmc-config - disable channels., Albert Chu, 2017/01/23
- Re: [Freeipmi-users] bmc-config - disable channels., Albert Chu, 2017/01/23