Nokia 6230i, gnokii & kernel 2.6.12-gentoo-r9

[Amaury Jacquot]

hi guys
I just received my new 6230i, and wanted to sync the address book, 
unfortunately, I have a few issues :(

first and foremost, I grabbed the cvs sources, just to make sure ;D

I compiled the dku-2 driver for 2.6 and installed it.

here's what I got in dmesg :

drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
drivers/usb/serial/usb-serial.c: USB Serial support registered for Nokia 
7600/6230/6230i/6170 DKU2 driver
Nokia DKU2: probe of 3-1:1.0 failed with error -1
Nokia DKU2: probe of 3-1:1.1 failed with error -1
Nokia AT Port:
Nokia DKU2 3-1:1.2: Nokia 7600/6230/6230i/6170 DKU2 driver converter 
detected
usb 3-1: Nokia 7600/6230/6230i/6170 DKU2 driver converter now attached 
to ttyUSB0
Nokia DKU2: probe of 3-1:1.3 failed with error -1
Nokia DKU2: probe of 3-1:1.4 failed with error -1
Nokia DKU2: probe of 3-1:1.5 failed with error -1
Nokia DKU2: probe of 3-1:1.6 failed with error -1
Nokia DKU2: probe of 3-1:1.7 failed with error -1
Nokia DKU2: probe of 3-1:1.8 failed with error -1
Nokia DKU2: probe of 3-1:1.9 failed with error -1
Nokia FBUS Port:
Nokia DKU2 3-1:1.10: Nokia 7600/6230/6230i/6170 DKU2 driver converter 
detected
usb 3-1: Nokia 7600/6230/6230i/6170 DKU2 driver converter now attached 
to ttyUSB1
usbcore: registered new driver Nokia DKU2
/home/sxpert/compile/gnokii/patches/kernel_2.6/nokia_dku2.c: v0.2 C Kemp
/home/sxpert/compile/gnokii/patches/kernel_2.6/nokia_dku2.c: Nokia DKU2 
Driver

this didn't seem right, but, I continued, just in case it would do 
something, unfortunately...

address@hidden ~/compile/gnokii $ gnokii --identify
GNOKII Version 0.6.7
LOG: debug mask is 0x1
LOG: rlpdebug mask is 0x1
LOG: xdebug mask is 0x1
phone instance config:
model: series60
port_device: /dev/ttyUSB1
connection_type: 9
init_length: 0
serial_baudrate: 19200
serial_write_usleep: -1
hardware_handshake: 0
require_dcd: 0
smsc_timeout: 100
connect_script:
disconnect_script:
rfcomm_cn: 1
sm_retry: off
Telephone interface init failed: Function or connection type not 
supported by the phone.
Quitting.

and

address@hidden ~/compile/gnokii $ xgnokii

Gdk-WARNING **: locale not supported by Xlib, locale set to C
LOG: debug mask is 0x1
LOG: rlpdebug mask is 0x1
LOG: xdebug mask is 0x1
Initializing connection...
phone instance config:
model: series60
port_device: /dev/ttyUSB1
connection_type: 9
init_length: 0
serial_baudrate: 19200
serial_write_usleep: -1
hardware_handshake: 0
require_dcd: 0
smsc_timeout: 100
connect_script:
disconnect_script:
rfcomm_cn: 1
sm_retry: off
fbusinit: error 6
GSM/FBUS init failed!
Initialization failed...
Inserting Event: 33
Phone connected. Starting monitoring...

I have attached my .gnokiirc

# This is a sample ~/.gnokiirc file.  Copy it into your
# home directory and name it .gnokiirc.
#

[global]

# Set port to the physical serial port used to connect to your phone.
# Linux version is:
port = /dev/ttyUSB1
#
# For MacOSX you will need something like:
# port = /dev/cu.USA28X1P1.1
#
# For Win32 you want to use:
# port = com1:
# or similiar.
#
# Use this setting also for the Bluetooth connection:
# port = aa:bb:cc:dd:ee:ff

# Set model to the model number of your phone. For the
# Symbian phones use:
# model = series60
# For other non-Nokia phones and when you want to use AT
# mode use:
# model = AT
# If you can't figure out what to put here read the FAQ.
# If it still doesn't help, consult gnokii-ml or #gnokii at freenode.
model = series60

# Initlength controls the number of characters sent to the
# phone during initialisation.  You can either set it to
# the word "default" or a positive integer.
#
# You can try setting this value if you want to connect
# to the phone quicker.  If you've never noticed the
# connection to be slow, it is suggested that you
# leave this alone.  Read the initialisation code in fbus-xxxx
# to understand what this changes if you're curious.
initlength = default

# The type of the connection, for IR set this to infrared or irda.
# For the nk6110 driver only infrared is valid for the IrDA connection.
# See Docs/gnokii-ir-howto for more detailes on this.
# If you have 6210/6250/7110 phone and dau9p cable (the one you can
# use with 6100 series and cannot use hardware modem from the phone)
# you may want to use 'dau9p' value to get faster initialization.
# If you use dlr3 or dlr3p cable for nokia phones in FBUS mode (ie.
# you don't use model = AT) you may want to use 'dlr3p' value here.
# Note that it is recommended and currently the best way to use this
# cable with nk6510 driver.
connection = dku2

# Set this to 'yes' if you want gnokii to set and check the lock file in
# /var/lock directory. It avoids potential conflicts with other serial
# port software (eg. minicom). If you have wrong permissions for the
# directory, a warning will be generated. If you don't want a lockfile, set
# it to 'no'.
use_locking = no

# Baudrate to use on serial port connections.
# Currently used only by models AT and BIP/CIMD. Defaults to 19200.
serial_baudrate = 19200

# Force waiting after each send character the specified usec time.
# Value -1 forces the fastest 'block' writing,
# value 0 writes each character separately without any explicite waiting,
# other positive values specify the appropriate 1/1000000 sec delaying.
# Siemens M20 requires at least "1"!  FIXME: Model-driven autodetection
#serial_write_usleep = 10000

# Force serial port handshaking mode, useful primarily for "AT" model.
# Gnokii "AT" model uses software handshake by default.
# Possible values: hardware (RTS/CTS - 7 wires) or software (XON/XOFF - 3 wires)
#handshake = software

# If defined (not commented out by '#') it will quit Gnokii anytime
# when DCD line will drop.
#require_dcd = 1

# If you are using a bluetooth connection, you can specify the rfcomm
# channel number here. Default value is 1.
#rfcomm_channel = 1

# There may happen various timeouts during the communication with the phone.
# This parameter enables the retransmission policy. Ie. if the phone doesn't
# respond, we send the frame again. This happend mainly with the older
# phones. You may want to enable it when you see mysterious timeouts.
# Be very carefull with this option. It is suspected to cause phone breakage
# with new DCT4 phones (like Nokia 6100). By default it is switched off
# (sm_retry = 0)
#sm_retry = 1

# Run the specified script(s) right after opening and initializing the device
# and before any communucation (right before closing for disconnect_script).
# You may find handy to use it to connect your modem to SMS Center
# when using BIP or CIMD protocols
# Non-absolute path is relative to the specific directory where gnokii is run!
#connect_script = /absolute/path/to/gnokii/Docs/sample/cimd-connect
#disconnect_script =

# When sending SMS you can experience timeouts. This is the feature of the
# overloaded SMSCs. The phones waits for the response from the SMSC confirming
# that it received the short message. When the SMSC is DoSed with many requests
# it will take more time to get the response. Adjust it to your needs. The
# value is given in seconds to wait. Defaults to 10 seconds. Set to 0 to wait
# forever.
smsc_timeout = 10

# Set bindir to point to the location of the various gnokiid binaries.
# In particular ensure that mgnokiidev is in this location, with
# permissions 4750, owned by root, group gnokii.  Ensure you
# are in the gnokii group and that the group exists...
[gnokiid]
bindir = /usr/sbin/

# Any entries in the following two sections will be set as environment
# variables when running the scripts.
# Handy for use for $VAR substitutions in your chat(8) script.
[connect_script]
TELEPHONE = 12345678
[disconnect_script]


# The following parameters control how libgnokii handle the debugging messages.
# Currently there are three categories: "debug" controls the libgnokii
# normal debug output, "rlpdebug" controls the debug output of the RLP
# subsystem, and "xdebug" is used by the xgnokii or smsd.

[logging]

# where to log the debug output (on: stderr)
debug = on

# where to log the rlp debug output (on: stderr)
rlpdebug = on

# where to log X debug output (on: stderr)
xdebug = on