[avrdude-dev] TPI Problem with Atmel-ICE on macOS

[address@hidden]

I've been unable to program an ATTiny10 device using AVRDUDE Version
6.3-20171130 on macOS 10.14.2 (18C54).  The ATTiny10 programs fine via
AVRDUDE if I use my AVR ISP mkII, but when I try to use my Atmel-ICE
programmer, I get the following response:

avrdude: Version 6.3-20171130
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is
"/var/folders/mt/7rrh06nw8xj05b0052g526300000gn/T/avr-toolchain/etc/avrdude.conf"
         User configuration file is "/Users/wholder/.avrduderc"
         User configuration file does not exist or is not a regular file,
skipping

         Using Port                    : usb
         Using Programmer              : atmelice_isp
avrdude: stk500v2_jtag3_open()
avrdude: usbhid_open(): Probing for max. packet size
avrdude: usbhid_open(): Setting max_xfer from DAP_Info response to 512
avrdude: Found CMSIS-DAP compliant device, using EDBG protocol
avrdude: jtag3_getsync()

avrdude: jtag3_edbg_prepare()
avrdude: jtag3_edbg_prepare(): connection status 0x01
avrdude: Sending sign-on command: 
avrdude: jtag3_edbg_send(): sending 3 bytes
avrdude: jtag3_recv(): Got message seqno 0 (command_sequence == 0)

[general] OK
         AVR Part                      : ATtiny10
         Chip Erase delay              : 0 us
         PAGEL                         : P00
         BS2                           : P00
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 0
         StabDelay                     : 0
         CmdexeDelay                   : 0
         SyncLoops                     : 0
         ByteDelay                     : 0
         PollIndex                     : 0
         PollValue                     : 0x00
         Memory Detail                 :

                                  Block Poll               Page                 
     
Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW 
MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
----- ---------
           signature      0     0     0    0 no          3   16      0     0    
0 0x00 0x00
                                  Block Poll               Page                 
     
Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW 
MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
----- ---------
           fuse           0     0     4    0 no          1   16      0     0    
0 0x00 0x00
                                  Block Poll               Page                 
     
Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW 
MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
----- ---------
           calibration    0     0     0    0 no          1   16      0     0    
0 0x00 0x00
                                  Block Poll               Page                 
     
Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW 
MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
----- ---------
           lockbits       0     0     0    0 no          1   16      0     0    
0 0x00 0x00
                                  Block Poll               Page                 
     
Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW 
MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
----- ---------
           flash          0     0   128    0 no       1024   16      0     0    
0 0x00 0x00

         Programmer Type : JTAG3_ISP
         Description     : Atmel-ICE (ARM/AVR) in ISP mode
avrdude: jtag3_getparm()
avrdude: Sending get parameter (scope 0x01, section 1, parm 0) command: 
avrdude: jtag3_edbg_send(): sending 6 bytes
avrdude: jtag3_recv(): Got message seqno 1 (command_sequence == 1)

[general] Data returned:
0x01 0x70 0x13 0x00 
         Vtarget         : 5.0 V

avrdude: jtag3_edbg_send(): sending 2 bytes
avrdude: jtag3_recv(): Got message seqno 2 (command_sequence == 2)
         SCK period      : 125.00 us

avrdude: jtag3_initialize(): part ATtiny10 has no ISP interface
avrdude: initialization failed, rc=-1
         Double check connections and try again, or use -F to override
         this check.


avrdude: jtag3_edbg_send(): sending 4 bytes
avrdude: jtag3_recv(): Got message seqno 3 (command_sequence == 3)
avrdude: stk500v2_jtag3_close()
avrdude: jtag3_close()
avrdude: Sending AVR sign-off command: 
avrdude: jtag3_edbg_send(): sending 3 bytes
avrdude: jtag3_recv(): Got message seqno 4 (command_sequence == 4)

[AVR] FAILED, reason: 0x90
avrdude: bad response to AVR sign-off command: 0xa0
avrdude: Sending sign-off command: 
avrdude: jtag3_edbg_send(): sending 4 bytes
avrdude: jtag3_recv(): Got message seqno 5 (command_sequence == 5)

[general] OK

avrdude: jtag3_edbg_signoff()

avrdude done.  Thank you.

Wayne



--
Sent from: http://avr.2057.n7.nabble.com/AVR-AVRdude-Dev-f3.html