Error: LookupError: KeyError: No
devices found for ----->
Device Address:
type: n200
*******************************************************************************************************
soporte@28:~$ uhd_find_devices
[INFO] [UHD] linux; GNU C++ version
7.5.0; Boost_106501;
UHD_3.14.1.1-0-g7c0291ad
--------------------------------------------------
-- UHD Device 0
--------------------------------------------------
Device Address:
serial: 3176CEA
addr: 192.168.10.2
name:
type: usrp2
*******************************************************************************************************
soporte@28:~$ uhd_usrp_probe
[INFO] [UHD] linux; GNU C++ version
7.5.0; Boost_106501;
UHD_3.14.1.1-0-g7c0291ad
[INFO] [USRP2] Opening a
USRP2/N-Series device...
[INFO] [USRP2] Current recv frame
size: 1472 bytes
[INFO] [USRP2] Current send frame
size: 1472 bytes
[WARNING] [USRP2] Unable to identify
device - assuming USRP2/N-Series
device
[WARNING] [UHD] Unable to set the
thread priority. Performance may be
negatively affected.
Please see the general application
notes in the manual for instructions.
EnvironmentError: OSError: error in
pthread_setschedparam
_____________________________________________________
/
| Device: USRP2 / N-Series
Device
|
_____________________________________________________
| /
| | Mboard: N???
| | mac-addr: 00:2c:00:00:00:24
| | ip-addr: 0.0.0.0
| | subnet: 0.0.0.0
| | gateway: 255.255.255.255
| | gpsdo: none
| | serial: 3176CEA
| | FW Version: 12.3
| | FPGA Version: 10.0
| |
| | Time sources: none, external,
_external_, mimo
| | Clock sources: internal,
external, mimo
| | Sensors: mimo_locked,
ref_locked
| |
_____________________________________________________
| | /
| | | RX DSP: 0
| | |
| | | Freq range: -50.000 to
50.000 MHz
| |
_____________________________________________________
| | /
| | | RX DSP: 1
| | |
| | | Freq range: -50.000 to
50.000 MHz
| |
_____________________________________________________
| | /
| | | RX Dboard: A
| | | ID: Basic RX (0x0001)
| | | Serial: 315A5DF
| | |
_____________________________________________________
| | | /
| | | | RX Frontend: AB
| | | | Name: BasicRX (AB)
| | | | Antennas:
| | | | Sensors:
| | | | Freq range: -250.000
to 250.000 MHz
| | | | Gain Elements: None
| | | | Bandwidth range:
500000000.0 to 500000000.0 step 0.0 Hz
| | | | Connection Type: IQ
| | | | Uses LO offset: No
| | |
_____________________________________________________
| | | /
| | | | RX Frontend: BA
| | | | Name: BasicRX (BA)
| | | | Antennas:
| | | | Sensors:
| | | | Freq range: -250.000
to 250.000 MHz
| | | | Gain Elements: None
| | | | Bandwidth range:
500000000.0 to 500000000.0 step 0.0 Hz
| | | | Connection Type: QI
| | | | Uses LO offset: No
| | |
_____________________________________________________
| | | /
| | | | RX Frontend: A
| | | | Name: BasicRX (A)
| | | | Antennas:
| | | | Sensors:
| | | | Freq range: -250.000
to 250.000 MHz
| | | | Gain Elements: None
| | | | Bandwidth range:
250000000.0 to 250000000.0 step 0.0 Hz
| | | | Connection Type: I
| | | | Uses LO offset: No
| | |
_____________________________________________________
| | | /
| | | | RX Frontend: B
| | | | Name: BasicRX (B)
| | | | Antennas:
| | | | Sensors:
| | | | Freq range: -250.000
to 250.000 MHz
| | | | Gain Elements: None
| | | | Bandwidth range:
250000000.0 to 250000000.0 step 0.0 Hz
| | | | Connection Type: Q
| | | | Uses LO offset: No
| | |
_____________________________________________________
| | | /
| | | | RX Codec: A
| | | | Name: ??????
| | | | Gain Elements: None
| |
_____________________________________________________
| | /
| | | TX DSP: 0
| | |
| | | Freq range: -200.000 to
200.000 MHz
| |
_____________________________________________________
| | /
| | | TX Dboard: A
| | |
_____________________________________________________
| | | /
| | | | TX Frontend: 0
| | | | Name: Unknown (0xffff)
- 0
| | | | Antennas:
| | | | Sensors:
| | | | Freq range: 0.000 to
0.000 MHz
| | | | Gain Elements: None
| | | | Bandwidth range: 0.0
to 0.0 step 0.0 Hz
| | | | Connection Type: IQ
| | | | Uses LO offset: No
| | |
_____________________________________________________
| | | /
| | | | TX Codec: A
| | | | Name: ad9777
| | | | Gain Elements: None
[WARNING] [UHD] Unable to set the
thread priority. Performance may be
negatively affected.
Please see the general application
notes in the manual for instructions.
EnvironmentError: OSError: error in
pthread_setschedparam
[WARNING] [UHD] Unable to set the
thread priority. Performance may be
negatively affected.
Please see the general application
notes in the manual for instructions.
EnvironmentError: OSError: error in
pthread_setschedparam
****************************************************************************************************************
I'm not completely sure what is
happening. it seems I have an USRP2. I
put it wit address 192.168.10.1, but
when I run uhd_find_devices is with
192.168.10.2
¿Could be that?
Isaac T.