Re: [Linphone-users] Linphonec errors on Debian build

[Charles Hamilton]

Hello again, Guillaume--

Sorry to ask for a clarification, but I'm still not entirely certain what you mean. Is this what you are suggesting:

1) I should recompile Linphone
2) then, instead of  ./configure only, it should be ./configure -xv OR ./configure -ogengl

3) then sudo make && sudo make install

4) then compare each of the builds ( -xv vs. -opengl) to check how video performs?

As an FYI, when doing the current build, I was directed by one of your colleagues to run ~/linphone/mediastreamer2 $ ./configure --disable-strict when compiling the mediastreamer2 part of the build since I was getting errors at that point. I'm assuming that doesn't affect your current recommendation, correct?

Thank you again for your speedy response!

Charles Hamilton

On Tue, Sep 17, 2013 at 9:01 AM, Guillaume Beraudo <address@hidden> wrote:

Hi,

You may compile linphone either with:
- xv;
- opengl.

See the ./configure

Guillaume

On Tue, Sep 17, 2013 at 08:44:04AM -0400, Charles Hamilton wrote:
> Hi Guillaume,
>
> Unfortunately, I'm very new to Linux. Can you be more specific about how I
> would do what you suggest?
>
> Thank you very much for your help.
> Charles Hamilton
>
>
> On Tue, Sep 17, 2013 at 8:19 AM, Guillaume Beraudo <
> address@hidden> wrote:
>
> > Hi,
> >
> > Have you compared builds with opengl and xv?
> >
> > Guillaume
> >
> >
> > On Mon, Sep 16, 2013 at 02:53:14PM -0400, Charles Hamilton wrote:
> > > Hello,
> > >
> > > I've now successfully compiled Linphone from source for Debian Wheezy and
> > > am running it on the Beaglebone Black.
> > >
> > > Audio seems fine. However, video remains a problem with extremely slow
> > > fps/latency. Here's an output from Linphonec:
> > >
> > > linphonec> ortp-error-no such method on filter MSGLXVideo, fid=16387
> > > method index=1
> > > Refreshing
> > > Registration on sip:sip.linphone.org successful.
> > > linphonec> -unknown source-(1)  : error 10 : Missing token, at offset -1
> > >     near [Index: 0 (Start: 0-Stop: 0) ='<missing '@'>', type<24> Line:
> > > 1 LinePos:24]
> > >      : Missing '@'
> > > ortp-error-header_contact parser error for [Contact: sip:192.xxx.xxx.xxx]
> > > ortp-error-No contact in response.
> > > ortp-error-presence op [0x811b8] receive an unexpected answer [200]
> > > -unknown source-(1)  : error 10 : Missing token, at offset -1
> > >     near [Index: 0 (Start: 0-Stop: 0) ='<missing '@'>', type<24> Line:
> > > 1 LinePos:24]
> > >      : Missing '@'
> > > ortp-error-header_contact parser error for [Contact: sip:192.xxx.xxx.xxx]
> > > ortp-error-No contact in response.
> > > ortp-error-presence op [0x5d450] receive an unexpected answer [200]
> > >
> > > Would anyone have any suggestions for troubleshooting this?
> > >
> > > Thank you very much for any advice.
> > > Charles Hamilton
> >
> > > _______________________________________________
> > > Linphone-users mailing list
> > > address@hidden
> > > https://lists.nongnu.org/mailman/listinfo/linphone-users
> >
> >
> > _______________________________________________
> > Linphone-users mailing list
> > address@hidden
> > https://lists.nongnu.org/mailman/listinfo/linphone-users
> >

> _______________________________________________
> Linphone-users mailing list
> address@hidden
> https://lists.nongnu.org/mailman/listinfo/linphone-users


_______________________________________________
Linphone-users mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/linphone-users