[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[PATCH 10/17] hw/misc/max111x: Use GPIO lines rather than max111x_set_in
From: |
Peter Maydell |
Subject: |
[PATCH 10/17] hw/misc/max111x: Use GPIO lines rather than max111x_set_input() |
Date: |
Sun, 28 Jun 2020 15:24:22 +0100 |
The max111x ADC device model allows other code to set the level on
the 8 ADC inputs using the max111x_set_input() function. Replace
this with generic qdev GPIO inputs, which also allow inputs to be set
to arbitrary values.
Using GPIO lines will make it easier for board code to wire things
up, so that if device A wants to set the ADC input it doesn't need to
have a direct pointer to the max111x but can just set that value on
its output GPIO, which is then wired up by the board to the
appropriate max111x input.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
---
include/hw/ssi/ssi.h | 3 ---
hw/arm/spitz.c | 9 +++++----
hw/misc/max111x.c | 16 +++++++++-------
3 files changed, 14 insertions(+), 14 deletions(-)
diff --git a/include/hw/ssi/ssi.h b/include/hw/ssi/ssi.h
index 4be5325e654..5fd411f2e4e 100644
--- a/include/hw/ssi/ssi.h
+++ b/include/hw/ssi/ssi.h
@@ -111,7 +111,4 @@ SSIBus *ssi_create_bus(DeviceState *parent, const char
*name);
uint32_t ssi_transfer(SSIBus *bus, uint32_t val);
-/* max111x.c */
-void max111x_set_input(DeviceState *dev, int line, uint8_t value);
-
#endif
diff --git a/hw/arm/spitz.c b/hw/arm/spitz.c
index 93a25edcb5b..fa592aad6d6 100644
--- a/hw/arm/spitz.c
+++ b/hw/arm/spitz.c
@@ -696,13 +696,14 @@ static void corgi_ssp_gpio_cs(void *opaque, int line, int
level)
static void spitz_adc_temp_on(void *opaque, int line, int level)
{
+ int batt_temp;
+
if (!max1111)
return;
- if (level)
- max111x_set_input(max1111, MAX1111_BATT_TEMP, SPITZ_BATTERY_TEMP);
- else
- max111x_set_input(max1111, MAX1111_BATT_TEMP, 0);
+ batt_temp = level ? SPITZ_BATTERY_TEMP : 0;
+
+ qemu_set_irq(qdev_get_gpio_in(max1111, MAX1111_BATT_TEMP), batt_temp);
}
static void corgi_ssp_realize(SSISlave *d, Error **errp)
diff --git a/hw/misc/max111x.c b/hw/misc/max111x.c
index abddfa3c660..3a5cb838445 100644
--- a/hw/misc/max111x.c
+++ b/hw/misc/max111x.c
@@ -131,12 +131,21 @@ static const VMStateDescription vmstate_max111x = {
}
};
+static void max111x_input_set(void *opaque, int line, int value)
+{
+ MAX111xState *s = MAX_111X(opaque);
+
+ assert(line >= 0 && line < s->inputs);
+ s->input[line] = value;
+}
+
static int max111x_init(SSISlave *d, int inputs)
{
DeviceState *dev = DEVICE(d);
MAX111xState *s = MAX_111X(dev);
qdev_init_gpio_out(dev, &s->interrupt, 1);
+ qdev_init_gpio_in(dev, max111x_input_set, inputs);
s->inputs = inputs;
@@ -153,13 +162,6 @@ static void max1111_realize(SSISlave *dev, Error **errp)
max111x_init(dev, 4);
}
-void max111x_set_input(DeviceState *dev, int line, uint8_t value)
-{
- MAX111xState *s = MAX_111X(dev);
- assert(line >= 0 && line < s->inputs);
- s->input[line] = value;
-}
-
static void max111x_reset(DeviceState *dev)
{
MAX111xState *s = MAX_111X(dev);
--
2.20.1
- Re: [PATCH 07/17] hw/misc/max111x: Don't use vmstate_register(), (continued)
- [PATCH 05/17] hw/arm/spitz: Implement inbound GPIO lines for bit5 and power signals, Peter Maydell, 2020/06/28
- [PATCH 08/17] ssi: Add ssi_realize_and_unref(), Peter Maydell, 2020/06/28
- [PATCH 09/17] hw/arm/spitz: Use max111x properties to set initial values, Peter Maydell, 2020/06/28
- [PATCH 10/17] hw/misc/max111x: Use GPIO lines rather than max111x_set_input(),
Peter Maydell <=
- [PATCH 11/17] hw/misc/max111x: Create header file for documentation, TYPE_ macros, Peter Maydell, 2020/06/28
- [PATCH 12/17] hw/arm/spitz: Encapsulate misc GPIO handling in a device, Peter Maydell, 2020/06/28
- [PATCH 13/17] hw/gpio/zaurus.c: Use LOG_GUEST_ERROR for bad guest register accesses, Peter Maydell, 2020/06/28