[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [PATCH 7/8] q800: wire up remaining IRQs in classic mode
From: |
Laurent Vivier |
Subject: |
Re: [PATCH 7/8] q800: wire up remaining IRQs in classic mode |
Date: |
Sat, 16 Oct 2021 20:09:38 +0200 |
User-agent: |
Mozilla/5.0 (X11; Linux x86_64; rv:78.0) Gecko/20100101 Thunderbird/78.11.0 |
Le 13/10/2021 à 23:21, Mark Cave-Ayland a écrit :
> Explicitly wire up the remaining IRQs in classic mode to enable the use of
> g_assert_not_reached() in the default case to detect any unexpected IRQs.
>
> Add a comment explaining the IRQ routing differences in A/UX mode based
> upon the comments in NetBSD (also noting that at least A/UX 3.0.1 still
> uses classic mode).
>
> Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
> ---
> hw/m68k/q800.c | 46 ++++++++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 46 insertions(+)
>
> diff --git a/hw/m68k/q800.c b/hw/m68k/q800.c
> index d55e6a7541..fa851e2ec9 100644
> --- a/hw/m68k/q800.c
> +++ b/hw/m68k/q800.c
> @@ -111,6 +111,37 @@ struct GLUEState {
>
> #define GLUE_IRQ_NUBUS_9 0
>
> +/*
> + * The GLUE logic on the Quadra 800 supports 2 different IRQ routing modes
> + * controlled from the VIA1 auxmode GPIO (port B bit 6) which are documented
> + * in NetBSD as follows:
> + *
> + * A/UX mode (Linux, NetBSD, auxmode GPIO low)
> + *
> + * Level 0: Spurious: ignored
> + * Level 1: Software
> + * Level 2: VIA2 (except ethernet, sound)
> + * Level 3: Ethernet
> + * Level 4: Serial (SCC)
> + * Level 5: Sound
> + * Level 6: VIA1
> + * Level 7: NMIs: parity errors, RESET button, YANCC error
> + *
> + * Classic mode (default: used by MacOS, A/UX 3.0.1, auxmode GPIO high)
> + *
> + * Level 0: Spurious: ignored
> + * Level 1: VIA1 (clock, ADB)
> + * Level 2: VIA2 (NuBus, SCSI)
> + * Level 3:
> + * Level 4: Serial (SCC)
> + * Level 5:
> + * Level 6:
> + * Level 7: Non-maskable: parity errors, RESET button
> + *
> + * Note that despite references to A/UX mode in Linux and NetBSD, at least
> + * A/UX 3.0.1 still uses Classic mode.
> + */
> +
> static void GLUE_set_irq(void *opaque, int irq, int level)
> {
> GLUEState *s = opaque;
> @@ -144,10 +175,25 @@ static void GLUE_set_irq(void *opaque, int irq, int
> level)
> case 1:
> /* Classic mode */
> switch (irq) {
> + case GLUE_IRQ_IN_VIA1:
> + irq = 0;
> + break;
> +
> + case GLUE_IRQ_IN_VIA2:
> + irq = 1;
> + break;
> +
> case GLUE_IRQ_IN_SONIC:
> /* Route to VIA2 instead */
> qemu_set_irq(s->irqs[GLUE_IRQ_NUBUS_9], level);
> return;
> +
> + case GLUE_IRQ_IN_ESCC:
> + irq = 3;
> + break;
> +
> + default:
> + g_assert_not_reached();
> }
> break;
>
>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
- Re: [PATCH 6/8] q800: route SONIC on-board Ethernet IRQ via nubus IRQ 9 in classic mode, (continued)
[PATCH 7/8] q800: wire up remaining IRQs in classic mode, Mark Cave-Ayland, 2021/10/13
- Re: [PATCH 7/8] q800: wire up remaining IRQs in classic mode,
Laurent Vivier <=
[PATCH 8/8] q800: add NMI handler, Mark Cave-Ayland, 2021/10/13
- Re: [PATCH 8/8] q800: add NMI handler, Laurent Vivier, 2021/10/15
- Re: [PATCH 8/8] q800: add NMI handler, Mark Cave-Ayland, 2021/10/15
- Re: [PATCH 8/8] q800: add NMI handler, Laurent Vivier, 2021/10/16
- Re: [PATCH 8/8] q800: add NMI handler, Mark Cave-Ayland, 2021/10/17
- Re: [PATCH 8/8] q800: add NMI handler, Laurent Vivier, 2021/10/17
- Re: [PATCH 8/8] q800: add NMI handler, Mark Cave-Ayland, 2021/10/20