[Slackware.it] digicom wave 54 e driver zd1211rw

[Antonio]

Ciao a tutti,
ho acquistato un adattatore wireless usb (digicom 54 wave) e non
riesco a farlo funzionare.
Ho copiato il firmware nella directory del /lib/firmware/zd1211 e
quando inserisco la chiavetta il comando lsmod mi da il seguente
output:

usb 2-1: new full speed USB device using ohci_hcd and address 4
usb 2-1: configuration #1 chosen from 1 choice
zd1211rw 2-1:1.0: firmware version 4725
zd1211rw 2-1:1.0: zd1211b chip 0ace:1215 v4810 full 00-02-72 AL2230_RF pa0 g--
zd1211rw 2-1:1.0: eth1

Dopo aver inserito la chiave do i seguenti comandi:
/etc/rc.d/rc.inet1 stop
ifrename
/etc/rc.d/rc.inet1 start

ifrename da il seguente warning:
Warning: Interface name is `wlan0' at line 1, can't be mapped reliably.
Il file /etc/iftab ha solo la riga:
wlan0 mac 00:02:72:57:AB:20

Alla fine di questa procedura il comando iwconfig  da come output:
wlan0     802.11g zd1211  ESSID:"linksys"
         Mode:Ad-Hoc  Frequency=2.462 GHz  Cell: 00:18:39:C6:02:1D
         Bit Rate=1 Mb/s
         Encryption key:kkk-kkkk-kkkk-kkkk-kkkk-kkkk-kk   Security
mode:restricted
         Link Quality:0  Signal level:0  Noise level:0
         Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
         Tx excessive retries:0  Invalid misc:0   Missed beacon:0

Ifconfig non rileva alcun indirizzo associato all'interfaccia wlan0
Utilizzo solo WPE.

Sugerimenti?
La slackware è la 11 ed il kernel è il 2.6.18 (ho scaricato i package)

Saluti a tutti.
Antonio

Ps allego i file /etc/rc.inet1.conf e /etc/rc.wireless.conf

# /etc/rc.d/rc.inet1.conf

# Config information for eth0:
IPADDR[0]=""
NETMASK[0]=""
USE_DHCP[0]=""
DHCP_HOSTNAME[0]=""

# Config information for eth1:
IPADDR[1]=""
NETMASK[1]=""
USE_DHCP[1]=""
DHCP_HOSTNAME[1]=""
# Default gateway IP address:
GATEWAY="192.168.1.1"

DEBUG_ETH_UP="yes"

## Example config information for wlan0.  Uncomment the lines you need and fill
## in your info.  (You may not need all of these for your wireless network)
IFNAME[4]="wlan0"
USE_DHCP[4]="yes"
WLAN_ESSID[4]="linksys"
WLAN_MODE[4]="Ad-Hoc"
WLAN_CHANNEL[4]="11"
WLAN_KEY[4]="kkkkkkkkkkkkkkkkkkkkkk"



# Wireless LAN adapter configuration

VERBOSE=1

case "$HWADDR" in

## NOTE : Comment out the following five lines to activate the samples below ...
## --------- START SECTION TO REMOVE -----------
## Pick up any Access Point, should work on most 802.11 cards
*)
  INFO="Sgueglia cfg"
  ESSID="linksys"
  MODE="Ad-Hoc"
  CHANNEL="11"
  RATE="auto"
  KEY="kkkkkkkkkkkkkkkkkkkkk"
;;
## ---------- END SECTION TO REMOVE ------------